Walter SURFOX MAX Serie Manual Del Usuario página 5

It is necessary to read carefully the instructions of this manual before any operation.
This manual provides the main information for adequate and safe installation, start-up, operation and maintenance
of the device.
This manual is intended to familiarize the user with this unit, its particular features, applications, limitations, and
the manufacturer's suggestions and recommendations.
The manual is an integral part of the device and should be stored with care until the unit is dismantled.
This manual reflects the state of the device at the time of delivery and cannot be regarded as inappropriate simply
because of later updates based on additional experience.
This device is built with extra durability to stand up to the heavy demands of industrial use. However, like any
piece of electrical equipment, care and safety should always be taken when using and maintaining this valuable
investment. With proper care and maintenance, your unit will provide years of reliable service.
WALTER
CUSTOMER ASSISTANCE DEPARTMENT
user information.
1. SAFETY
WALTER SURFOX
's
in accordance
governing the manufacture, performance and
safety of industrial products.
All persons in charge of device installation,
operation, maintenance
possess the appropriate technical qualifications
and must meticulously comply with the
provisions of this user manual.
To reduce the risk of fire, electric shock, and
personal injury, always follow basic safety
precautions when using this equipment.
O
BLIGATIONS OF THE PERSON IN CHARGE OF THE DEVICE
The owner of the device and/or any person responsible for
safety are required to:
• Ensure that all users of the device are adequately trained as
regards current occupational health and safety regulations.
• Ensure that all users of the device have read this user manual
in its entirety and have understood all of it, in particular the
sections on safety standards.
• Periodically check that all personnel always operate in
compliance with safety standards.
• Inspect the equipment regularly to ensure that it is operating
properly and performing its intended function. Damaged or
defective parts must be repaired or replaced immediately
by WALTER qualified personnel only. Refer to spare parts
list for the ordering number and contact a WALTER Factory
Service Center or WALTER Authorized Service Center.
• Periodically check that all the safety signs affixed to the
device (data plate, stickers bearing danger symbols, etc.)
are clearly legible and not damaged, overwritten, removed
or obscured by other objects.
MAX is produced
with applicable standards
and repair must
(walter.com) is at your disposal to provide all the marketing and
O
BLIGATIONS OF THE USER
Personnel authorized to use the device must:
• Operate in accordance with current occupational health and
safety regulations.
• Read this user manual carefully, paying particular attention
to the sections on safety standards.
• Sign a document in which they declare that they have read
and understood this manual, and that they undertake to
follow all the instructions contained therein.
• When working, always wear personal protective equipment
and clothing (see chapter 1.1).
• Use the device only as explained in this manual; improper
use increases the risk of accidental personal injury and/or
property damage.
• Stay alert at all times when handling this unit. Watch what
you are doing. Use common sense. Do not operate the
device if you are tired. Never leave it running unattended.
• Do not use the unit if the switch does not turn ON and OFF.
• Hold the wand firmly. Do not overreach, maintain good
footing and balance at all times.
• Keep the work area clean and well lit. A cluttered environment
invites accidents. Remove any material that may be ignited
by sparks. Do not use this equipment in the presence of
flammable liquids or gases are. Keep handles clean, dry and
free from cleaning solution, oil and grease. Do not use in
rain, damp or wet locations.
• Take appropriate precautions and always secure the device
during periods when the workstation is not manned (such as
during breaks or at the end of the shift).
• Do not abuse the power cord. Never pull or lift this unit by
its cord or yank to disconnect it from the outlet. Keep the
cord away from heat, oil, and sharp edges. Inspect the cord
regularly and have it replaced by a WALTER Factory Service
Center or WALTER Authorized Service Center if damaged.
• Keep children and others away from the work area. Make
sure no one is under you when working in high places. Do
not allow unqualified persons handle this machine.
5