Publicidad
Idiomas disponibles
Idiomas disponibles
Power-cod Protection.
The unit is provided with an
attachment plug with overload protection.
This
IS
a safety
feature.
See operating instructions for replacement or
resetting of protective device.
If replacement of the plug is
required, be sure the service technician has used a
replacement
plug specified by the manufacturer that has the
same overload protection as the original plug.
CXmrloacting - Do not alk~w anything to rest on the power
cord. Do not overload wall outlets and extension cords
because this can result in fire or electric shock. Do not place
the unit in an area where people will walk on the cord.
Qildoor
Antenna
Power lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall onto such
power lines or circuits.
When installing an outside antenna
system, extreme care should be taken to avoid touching
power lines or circuits because contact with them may be
fatal.
outdoor
Antenna Grounding - [f an outside antenna or
cable system is connected to the unit, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges.
Section 810 of the National Electrical Code, ANS1/
NFPA No.70, provides information with regard to proper
grounding of the mast anl~ supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, locatlon of antenna-discharge
unit,
connection to grounding electrodes, and requirements for
the grounding electrode.
See the figure.
Antenna Grounding Acc xdlng to the National Electrical Cord
H
, ANTENNA LEAD IN WIRE
/'
GROUND CLAI'
T=
=
ELECTRIC
SERVICE
EQUIPMENT
)
"'---d
1~~
GROUND CLAMPS
(NEC ART 250 PART H)
NEC-NATIONAL
ELECTRICAL (: ODE
Lightning
For added protection during a lightning storm, or when left
uni~ttended and unused for long periods of time, unplug the
unit from the wall outlet and disconnect the antenna or cable
system.
This will prevent damage to the unit due to
lightning and powerlme surges.
~&ntenancx3
Cleaning -
Unplug the unit from the wall outlet before
cleaning.
Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
Damaae Reauirirwt Service
Unplug the unit from the wail outlet and refer servicing to
qualified service personnel under the following conditions:
1) When the power cord or plug is damaged or frayed.
2) If liquid has been spilled into the unit.
3) If the unit has been exposed to rain or water.
4) If the unit does not operate normally when following
the operating instructions.
Adjust only those controls
that are covered by the operating instructions because
Improper adjustment of other controls may result in
damage to the unit and will often require extensive
work by a qualified technician to restore the unit to
normal operation.
5) If the unit has been dropped or the cabinet has been
damaged.
6) When the unit exhibits a distinct change in
performance - this indicates a need for service.
Do not attempt to service the unit yourself because opening
or removing covers may expose you to high voltage or other
hazards.
Refer all servicing to qualified service personnel.
Replacement
Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer
or having the same
characteristics
as the original part. Unauthorized
substitutions
may result in fire, electric shock or other
hazards.
Safety Check -
After completion of any service or repairs to
the unit, ask the service technician to perform a safety
check to ensure that the unit is in proper operating
condition.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NIEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground should be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
OVUNER'S RECORD
For your convenience,
record the model number and
serial number
(you
will find
them
on the
rear
of your
set)
in the space provided below. Please refer to them when
you contact your AIWA dealer in case of difficulty.
Model No.
[—_–.]
Serial No.
'–"---1
~
ENGLISH
2
Publicidad
