TSG ALL TERRAIN Manual Del Usuario página 4

OWNER'S MANUAL ALL TERRAIN HELMET
Thank you. You have chosen a TSG safety product designed especially for action sport and biking.
Please read the following information carefully. Correctly used and cared for, it will keep you better
protected and satisfied.
TESTING, APPROVAL & USE
The All-Terrain is the first ever action sport helmet designed, tested and certified for all sports and
all seasons. This helmet is intended for bicycle, skateboarding, wakeboarding, (E-) foil surfing and
skiing/snowboarding use only and not for motorized vehicle use including motorcycles or mopeds! This
helmet is designed to protect impact caused by falling or ejected objects and collision of parts of the
body with an obstacle.
This helmet is CE marked to denote compliance with the Personal Protective Equipment Regulation
(EU) 2016/425. The helmet demonstrates conformity with the Essential Health and Safety Require-
ments (EHSR) of Regulation (EU) 2016/425 as transposed into UK law.
The following European Standards and protocols have been used in the evaluation of this product.
EN 1078
The helmet meets the requirements of European standard EN 1078+A1:02.2013: Helmets for pedal
cyclists and for users of skateboards and roller skates.
CSN-001
The helmet meets the rquirements of CSN-001: Test Protocol for watersports helmets.
EN 1077 B
The helmet meets the requirements of European standard NF EN 1077:12/2007 – Helmets for alpine
skiers and snowboarders.
Class A and Class B helmets are for Alpine skiers, snowboarders and similar groups. Class A helmets of-
fer comparatively more protection. Class B helmets may offer greater ventilation and better hearing but
protect a smaller area of the head and offer a lower penetration resistance. The protection class can be
taken from the label inside the helmet. The helmet satisfies the requirements specified in the standard
in terms of shock absorption, slipping safety and resilience of straps and closures.
CPSC
The helmet complies with CPSC 16 CFR 1203 (Consumer Product Safety Commission) Safety Standard
for Bicycle Helmets for Adults and Children Age 5 and older.
ASTM F2040
The helmet passes the American National Standard Specification ASTM F2040-18 for Helmets Used
for Recreational Snow Sports.
Find the declaration of conformity for each model on our website:
www.ridetsg.com/service/declaration-of-conformity/
6 – ENGLISH
WARNING NOTICES - WARNING!
• For maximum protection the helmet must be fitted and attached properly to the wearer's
head in accordance with the manufacturer's fitting instructions.
• This helmet is designed to absorb shock by partial destruction of the energy absorbing
liner. This damage may not be visible to the user. Therefore, if subjected to a severe impact
or blow, the helmet should be destroyed and replaced even if it appears undamaged.
• A helmet can only provide a level of protection for areas that it covers.
It does not protect your neck.
• A helmet can only protect if it fits well and properly to your head and if it is correctly buckled.
• No helmet can protect against all possible impacts.
• Do not modify or remove any of the original component parts of the helmet other than as
recommended by the manufacturer, as it may affect its protective capacity. The helmet must
not be modified to attach accessories in a manner not recommended by the manufacturer.
Do not remove the original stickers on the inside of the helmet.
• Some common substances can cause damage to the helmet, though it may not be visible to
the user. The use of any solvents, transfers, adhesives, paints or cleaning solutions can cause
damage to the helmet and make it ineffective in the result of an accident.
• This helmet is for pedal cyclists, skate boarders and roller skaters. ATTENTION! Not for motor
vehicle use.
• Warning! This helmet should not be used by children while climbing or doing other activities
when there is a risk of strangulation/hanging if the child gets trapped with the helmet.
CLEANING
Wipe only with a soft damp cloth in gentle soap or mild detergent in cold water, rinse by wiping with a
soft cloth damped in cold water and dry with a soft cloth. Comfort padding can be removed and hand
washed and air dried.
STORAGE AND TRANSPORTATION
After each use, allow your helmet to air dry and then store in a cool, dry place. Do not expose your hel-
met to impact or external force during transport. Helmets will be damaged if exposed to temperatures
exceeding 65°C. Vehicles and storage bags can exceed this on very hot days. Heat damaged helmets
will have random disfigured areas where the texture appears bubbly and uneven. If damaged, helmets
should be destroyed and replaced immediately.
MAINTENANCE AND OBSOLESCENCE
For maximum performance, your TSG product must be inspected prior to each use. Stop using the
helmet if any components show signs of damage or are worn, cracked, and/or deformed, or if the inside
foam has deteriorated. Helmets have a limited life span in use and should be replaced every 3-5 years
under normal use conditions, but at the latest after 8 years from date of manufacture (see product
label). If you know or suspect that your helmet has been damaged or exposed to any abnormal force,
destroy and replace it. Please dispose of it in an environmentally-friendly manner. Do not make any
modifications to the helmet, this includes the outer shell, the inner EPS liner or chin strap, any modifi-
cations will void all warranties and affect the helmet's performance.
ENGLISH – 7