Publicidad
Idiomas disponibles
Idiomas disponibles
Free Cycles
This is established by setting the cycle price to zero. When this
happens, 'SELECT CYCLE' will appear rather than a cycle price.
Display
After the washer has been installed and plugged in, the display
will show "0 MINUTES." Once the washer has been plugged in
and the washer door opened and closed, the display will show
the price. In washers set for free cycles, the display will flash
"SELECT CYCLE."
Control Set-Up Procedures
IMPORTANT: Read all instructions before operating.
PD Models: Insert service access door key, turn, and lift to
■
remove service access door.
PR Models: Once the debit card reader is installed
■
(according to the reader manufacturer's instructions), the
set-up mode can only be entered by inserting a set-up card
(supplied by the reader manufacturer) into the card slot.
If a set-up card is not available, diagnostic modes can be
entered by removing service connector on the circuit board
or by using the Service Access Code (see Service Access
Code section) for PR washers set up for free vend.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
IMPORTANT: Unplug washer or disconnect power before
opening the console. To access service connector:
Unplug washer or disconnect power.
■
Open console, disconnect plug on service connector, close
■
console.
Plug in washer or reconnect power. The washer is now in
■
the set-up mode. The lower fabric setting keypads and the
digital display are used to set up the controls. The display
can contain 4 numbers and/or letters and a decimal point.
These are used to indicate the set-up codes and related
code values available for use in programming the washer.
12
How to use the keypads to program the controls
1. The POWER WASH – UPPER LEFT keypad is used to adjust
the values associated with set-up codes. Pressing this keypad
will increment the value. Rapid adjustment is possible by
holding this keypad down.
2. The TEMPERATURE – LOWER LEFT keypad is used to adjust
the values associated with set-up codes. Pressing this keypad
will decrement the value. Rapid adjustment is possible by
holding this keypad down.
3. The EXTRA RINSE – LOWER MIDDLE keypad will advance
through the set-up codes. Pressing this keypad will advance
to the next available set-up code. Holding this keypad down
will automatically advance through the set-up codes at a rate
of one (1) per second.
4. The DELICATES – UPPER RIGHT keypad is used to select or
deselect options.
Start Operating Setup
NOTE: Prior to operation, a payment system or an OPL kit must
be installed on PD models as part of the setup.
Before proceeding, it is worth noting that, despite all of the
options available, an owner can simply choose to uncrate a new
commercial washer, hook it up, plug it in, and have a washer that
operates. Washers are preset at the factory for an 11 minutes
wash period and 3 rinses (no extra rinse).
Setup Codes
FOR PR MODELS: The set-up codes are the same as for the
"PD" model except where noted.
The set-up code is indicated by the 1 or 2 left-hand characters.
The set-up code value is indicated by the 2 or 3 right-hand
characters. The first code shown in each section is the Factory
Default setting.
CODE
6 07
REGULAR CYCLE PRICE (Factory Default)
6
07
Represents the number of Coins or Debit inputs
needed to start the washer; may adjust from 0–39.
(See VALUE OF COIN 1.) Advance from 0–39 by
pressing keypad.
With coin slide activation, this code represents
the number of push-in actuations of a coin slide
to start the washer.
6 01 setting would represent one coin slide
actuation.
NOTE: For coin slide activation, replacement
of the meter case is necessary.
6
00
PR MODELS ONLY: Factory default of 0.
Press the keypad once to advance to next code.
g
WASH LENGTH
7 11
7 11
This is the number of minutes for Wash. Washer
comes from the factory preset with 11 minutes.
Choose from 9–17 minutes by pressing the keypad.
Press the keypad once to advance to next code.
g
NOTE: This option does not apply.
8 00
ADDITIONAL RINSE OPTION
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
8
00
Not Selected 'OFF'.
8
Ar
Selected 'ON'. Cannot be combined with the Super
Cycle rinse option.
Press the keypad once for this selection.
g
Press the keypad once to advance to next code.
9 00
CYCLE COUNTER OPTION
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
EXPLANATION
Publicidad
