Publicidad
Idiomas disponibles
Idiomas disponibles
SERVICE ACCESS CODE
This code can be entered to access service mode without
removing the console. It only functions on washers set up for
0 vend price without any Special Pricing setup, and the Coin/
Debit Option must be set to "J._d". If the washer is not in failure
mode, the door must be opened to proceed.
To enter the Service Access Code, press these keypads
in the following order: 1–upper left, 2–lower right, 3–upper right,
4–lower left.
NOTE: If the Service Access Code procedure is not completed
properly, as noted above, there is a 15 seconds delay before it
can be attempted again.
There are 3 options to exit from the Service Mode:
1. Power down the washer; then reapply power.
2. Wait 2 minutes without touching any keypads (without
diagnostic modes running).
3. From Set-Up Code 8, press keypad #1 for 4 seconds.
WASHER CARE
Cleaning Your Washer
Cleaning the Door Seal/Bellow
1. Open the washer door and remove any clothing or items from
the washer.
2. Inspect the colored seal/bellow between the door opening
and the drum for stained areas. Pull back the seal/bellow
to inspect all areas under the seal/bellow and to check for
foreign objects.
A. Seal/Bellow
3. If stained areas are found, wipe down these areas of the seal/
bellow, using the procedure that follows.
a)
Mix a dilute solution, using 177 mL (3/4 cup) of liquid
chlorine bleach, and 3.8 L (1 gallon) of warm tap water.
b)
Wipe the seal/bellow area with the dilute solution,
using a damp cloth.
c)
Let stand 5 minutes.
d)
Wipe down area thoroughly with a dry cloth and let
the washer interior air dry with door open.
IMPORTANT:
Wear rubber gloves when cleaning for prolonged periods.
■
Refer to the bleach manufacturer's instructions for proper use.
■
Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes
in combination with liquid chlorine bleach to thoroughly clean the
inside of the washer.
NOTES:
Read these instructions completely before beginning the
■
cleaning process.
A
If necessary, the cleaning cycle may be interrupted by
■
pressing the keypad twice. However, this will not immediately
stop the cycle. The washer will continue with several rinse
and drain steps to ensure that all remaining bleach is rinsed
from the washer.
Begin procedure
1. Open the washer door and remove any clothing or items from
the washer.
2. Use liquid chlorine bleach:
Open the dispenser drawer and immediately add
160 mL (2/3 cup) of liquid chlorine bleach to the bleach
compartment.
NOTE: Do not add any detergent to this cycle. Use of more
than 160 mL (2/3 cup) of bleach will cause product damage
over time.
3. Close the washer door and the dispenser drawer.
4. Enter Set-Up ModePress Upper Right Keypad for 2 seconds.
P01 will be diplayed. Press Lower Middle Keypad 7 times to
advance to P08. Press Start Keypad.
NOTE: The door will lock and the drum will rotate; then the
door will unlock, lock again, and the cycle will continue.
The washer will not fill, but the drum will rotate while
■
the washer runs a short sensing cycle. This will take
approximately 3 minutes.
5. The cycle will determine whether clothing or other items are
in the washer.
a)
If no items are detected in the washer, it will proceed
to Step 7.
b)
If any items are detected in the washer, "rL" or "F-34"
will be displayed. Then the door will unlock.
Press to cancel the failure code.
■
Then repeat steps 1, 3, and 4 to start the cycle again.
6. Once the cycle has begun, allow the cycle to complete.
7. After the cycle is complete, leave the door open slightly,
to allow for better ventilation and drying of washer interior.
Always do the following to maintain washer freshness:
Use only "HE" High Efficiency detergent.
■
Leave the door slightly open after each cycle to allow
■
for better ventilation and drying of washer interior.
Clean the washer monthly using the Washer Maintenance
■
Procedure, and 160 mL (2/3 cup) of liquid chlorine bleach.
If the procedure does not sufficiently improve the washer
■
freshness, please evaluate your installation and usage
conditions for other causes.
Cleaning the Exterior
Use a soft, damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.
Cleaning the Dispenser Drawer
The dispenser drawer is removable for easy cleaning.
1. Unlock the dispenser drawer by pressing the Release Lever.
Remove the drawer.
2. Remove the inserts (the siphon from the softener and bleach
compartments).
3. Wash the parts under running water.
NOTE: Do not wash components in the dishwasher.
4. Replace the inserts and return the dispenser to the drawer.
15
Publicidad
