Maytag MHN33PD Instrucciones De Instalación página 14

CODE
d. 00 Not Selected 'OFF'. Used with coin drop or card
readers.
d. CS Selected 'ON'. Press the keypad 3 consecutive
times for this selection.
NOTE: This option needs to be set to "00" unless
the meter case has been changed to accept a coin
slide device.
When coin slide mode is selected 'On', set b. equal
to value of vend price. Set setup code 6 (regular
cycle price) and setup code 3 (special cycle price)
to number of slide pushes. If washer is set up as
"CS" and a coin drop is installed, it will not register
coins.
NOTE: For coin slide activation, replacement
of the meter case is necessary.
g Press the keypad once to advance to next code.
E. 00 ADD COINS OPTION
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'. This option causes the customer
display to show the number of coins (coin 1) to
enter, rather than the amount.
E. 00 Not Selected 'OFF'.
E. AC Selected 'ON'. Press the keypad 3 consecutive
times for this selection.
g Press the keypad once to advance to next code.
F. 00 ENHANCED PRICING OPTION
F. 00 Not Selected 'OFF'.
F. CP Cycle-Based pricing enabled. This option allows
configuration of different prices for cold, warm, and
hot water cycles.
F. Su Super Cycle pricing enabled. This option allows
customers to upgrade cycles by depositing extra
money. Setup codes "H." and "h." will be displayed
only when this option is enabled. Press the keypad
once for this selection.
Press the keypad once to advance to next code.
g
SUPER CYCLE UPGRADE PRICE
H. 01
(Skipped unless super cycle pricing is enabled.)
H. 01 This represents the number of coin 1 required to
upgrade a base cycle to a super cycle. Advance
from 0–39 by pressing the keypad.
g Press the keypad once to advance to next code.
h. 01 SUPER CYCLE TYPE
(Skipped unless Super Cycle pricing is enabled.)
h. 01 This represents the Super Cycle upgrade option.
Press the keypad to step through upgrade options
1–3 as follows:
01 – enhanced wash, extra 3 minutes of wash
tumble in addition to the programmed wash time.
02 – extra rinse for all cycles.
03 – both 01 and 02.
Press the keypad once to advance to next code.
g
COIN/DEBIT OPTION
J. Cd
J. Cd Both coin & debit selected. Press the keypad
3 consecutive times to change this selection.
J. C_ Coins selected, debit disabled. Press the keypad
3 consecutive times to change this selection.
J. _d Debit card selected, coins disabled. This is the
factory default for PR models. Press the keypad
3 consecutive times to change this selection.
J. Ed Enhanced Debit is self-selected when a Generation
2 card reader is installed in the washer. The Ed
option cannot be manually selected or deselected.
g
Press the keypad once to advance to next code.
14
EXPLANATION CODE
PRICE SUPPRESSION OPTION
L. 00
This option causes the customer display to show
'ADD' or 'AVAILABLE' rather than the amount of
money to add. (Used mainly in debit installations.)
L. 00 Not Selected 'OFF.'
L. PS Selected 'ON.' Press the keypad once for this
selection.
Press the keypad once to advance to next code.
g
CLEAR ESCROW OPTION
n. CE
When selected, money held in escrow for
30 minutes without further escrow or cycle activity
will be cleared.
00 Not Selected 'OFF'.
CE Selected 'ON'. Press the keypad once for this
selection.
g Press the keypad once to advance to next code.
r. 800 TOP SPIN SPEED RPM
r. 800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds by
pressing the keypad. Factory pre-set for 800 rpm.
g Press the keypad once to advance to next code.
U. 00 PENNY INCREMENT OFFSET
U. 00 This option is not supported for European Models
and the value must be set to 00.
g Press the keypad once to advance to next code.
PREWASH LENGTH
A1. 00
A1. 00 This is the number of minutes of Prewash. Choose
0 to disable the prewash or select between 2 and
7 minutes by pressing the keypad.
g
Press the keypad once to advance to next code.
A2. 03 FINAL SPIN LENGTH
A2. 03 This is the number of minutes of final high-speed
spin. Choose from 3–8 minutes by pressing the
keypad.
Press the keypad once to advance to next code.
g
If cycle counter (9 0C) is selected, the following is true:
1 00 Number of cycles in HUNDREDS.
2 00 Number of cycles in ONES.
This is 'VIEW ONLY' and cannot be cleared.
g Press the keypad once to advance to next code.
If money counter (1.0C or 1.C0) is selected, the following
is true:
3 00 Currency amount in HUNDREDS.
4 00 Currency amount in ONES.
5 00 Currency amount in HUNDREDTHS.
END OF SETUP PROCEDURES
EXIT FROM SETUP MODE
PD Models: Reinstall access door.
■
PR Models:
■
– Unplug washer or disconnect power.
– Open console, reinsert plug into service connection, close
console.
– Plug in washer or reconnect power.
EXPLANATION
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225
3 01 = 100.00
4 68 = 68.00
5 75 = 00.75
TOTAL = 168.75