cleanAIR 72 03 00.01 Manual Del Usuario página 4

8. List of products and spare parts
Table 1: Product name and product code
Product code Product description
72 03 00.01 Protective face shield UniMask, grey
72 03 00.02 Protective face shield UniMask, blue
72 03 00.03 Protective face shield UniMask, orange
72 03 00.04 Protective face shield UniMask, red
72 03 00.08 Protective face shield UniMask, neoprene
Table 2: List of spare parts
Product code Product description
72 03 20/10 Protection film UniMask, pack of 10 pcs
72 03 40 Head band UniMask
72 03 45 Head harness UniMask 5-point
72 90 00 Spare visor TR1, clear
72 90 01 Spare visor TR1, yellow
72 90 03 Spare visor TR1, shade 3
72 90 05 Spare visor TR1, shade 5
Spare protective visor TR1, clear, aPA, chemicaly
72 90 90
resistant
72 91 00 Spare visor CR1, clear, CP
72 03 50.01 Face seal UniMask, grey
72 03 50.02 Face seal UniMask, blue
72 03 50.03 Face seal UniMask, orange
72 03 50.04 Face seal UniMask, red
72 03 50.08 Face seal UniMask, neoprene
72 03 60 Protective hood UniMask, short
72 03 61 Protective hood UniMask, long
72 03 62 Protective hood UniMask, washable fabric
9. Approved combinations
Product code Product description
30 00 00PA AerGO
51 M0 00FC MedicAER
81 00 00PA Basic
51 00 00FCA Chemical 2F
52 00 00CFA Chemical 3F
63 00 00 Pressure
67 00 00 Pressure Flow Master
The level of protection is also ensured even if classic rimmed
glasses are used.
10. These products are approved in compliance
with the following standards:
Notified body for the CE approval:
EN 12941:1998+A2:2008 & EN 14594:2005
Occupational Safety Research Institute, v.v.i.
Jeruzalémská 1283/9, 110 00 Prague 1, Czech Republic
Notified body 1024
EN 166
Institute for testing and certification, a.s.
Třída Tomáše Bati 299, 764 21 Zlín, Czech Republic
Notified body 1023
Declaration of Conformity is available at:
https://www.clean-air.cz/doc
4
Level of protection
TH3
®
TH3
TH3
TH3
TH3
2A
3B
Markings and symbols according to EN 166:
UniMask frame marking:
®
EN 166 MS 3 4 5 9 FT B 5/2-5
UniMask compatible visors marking
®
Visor Description
72 90 00 TR1, clear PC
72 90 01 TR1, yellow PC
72 90 03 TR1, shade 3
PC
72 90 05 TR1, shade 5
PC
72 90 90* TR1, clear aPA
72 91 00 CR1, clear CP
72 91 01* CR1, clear PC
* not suitable for use in ATEX zone
Marking description
MS Manufacturer identification (MALINA – Safety s.r.o.)
166 Standard EN 166
3; 5 Shade number - welding filter (EN 169)
2C Code number - UV protection with good colour recog-
nition (EN 170)
2 Code number - UV protection (EN 170)
1,2; Shade number - UV protection (EN 170)
3; 5
1 Optical class
A (T) Mechanical strenght - High energy impact (190 m/s)
B (T) Mechanical strenght - Medium energy impact (120 m/s)
F (T) Mechanical strenght - Low energy impact (45 m/s)
S Mechanical strenght - Increased robustness
If the letter (A, B, F) is followed by the letter „T", then the frame
protects against impact at extreme temperatures (-5°C / +55°C)
3 Field of use - Liquids (droplets or splashes)
4 Field of use - Large dust particles
5 Field of use - Gas and fine dust particles
9 Field of use - Splashes of molten metal and penetration
of hot solids
K Resistance to surface damage by fine particles
N Resistance to fogging
UNIMASK – РЪКОВОДСТВО НА ПОТРЕБИТЕЛЯ –
БЪЛГАРСКИ ЕЗИК
Важно
За вашата собствена безопасност прочетете и запомнете
следните инструкции преди употреба. Ако имате въпроси,
се обърнете към производителя или дистрибутора. Запазете
ръководството за бъдещи справки.
Visor marking Field
of use
2C-1,2 MS 1 FT B 9 K N 3 4 5 9
2C-1,2 MS 1 FT B 9 K N 3 4 5 9
3/2-3 MS 1 FT B 9 K N 3 4 5 9
5/2-5 MS 1 FT B 9 K N 3 4 5 9
MS 1 FT 3 4
MS 1 S N 3 4 5
MS 1 FT 3 4 5