3. Candle filter only: Take out the candle filter (special
accessories).
Illustration G
4. Insert coarse dirt filter in the filter frame.
5. Insert the filter frame into the suction head.
6. Close the filter cover until it audibly latches into
place.
Inserting the pre-filter
1. Unlock and remove the suction head.
2. Remove the cable clip of the disposal pump.
3. When inserting the pre-filter, push it over the suction
hose port until it touches the container wall.
4. Insert the cable clip of the disposal pump.
5. Fit and lock the suction head.
Connecting the disposal hose
1. Remove the cap.
Illustration H
2. Connect the disposal hose (nominal width 3/4" or
larger).
Draining the waste water
WARNING
Environmental pollution!
Environmental pollution due to improper disposal in
waste water.
Observe the local waste water treatment regulations.
1. Drain the waste water via the drain hose.
Illustration I
General
ATTENTION
Danger of coarse dirt
Risk of damage to the suction motor.
Never remove the coarse dirt filter when vacuuming.
● The device switches off automatically when the
maximum fluid level is reached.
● On completion of wet vacuum cleaning: Clean the
float, container and, if necessary, the disposal pump
with a damp cloth and dry.
Dry vacuuming
Note
Before dry vacuum cleaning: Remove the disposal
pump and install the flat fold filter or candle filter.
Note
A flat fold filter or candle filter should generally be used
for dry vacuuming.
General
ATTENTION
Danger due to fine dust entering
Risk of damage to the suction motor.
Never remove the flat fold filter or candle filter when vac-
uuming.
● When vacuuming fine dust, a fleece filter (special
accessory) or dust bag (special accessory) can also
be used.
Removing the disposal pump
1. Unplug the mains plug of the disposal pump.
2. Unlock and remove the suction head.
3. Take out the cable holder of the disposal pump and
replace it with a latch plate.
Illustration J
4. Pull the pre-filter over the suction hose port and re-
move it.
5. Unscrew the union nut of the disposal pump.
14
6. Remove the disposal pump and plastic insert from
the container.
7. Attach the cap instead of the disposal hose.
Illustration K
8. Fit and lock the suction head.
Installing the flat fold filter or candle filter
Note
A flat fold filter or candle filter is not included in the
scope of delivery.
1. Open the filter cover.
2. Remove the filter frame.
3. Remove the coarse dirt filter from the filter frame.
4. Flat fold filter only: Insert the flat fold filter (special
accessory) into the filter frame. During insertion, en-
sure that the flat fold filter is flush on all sides. Insert
the filter frame into the suction head.
5. Candle filter only: Insert the candle filter (special ac-
cessory) into the suction head.
6. Close the filter cover until it audibly latches into
place.
Installing the brush strip
1. Remove the squeegee.
Illustration L
2. Install the brush strip.
Installing the fleece filter bag
1. Unlock and remove the suction head.
2. Fit the fleece filter bag (special accessory).
Illustration M
3. Fit and lock the suction head.
Installing the dust bag
Note
The dust bag opening must be pulled fully over the suc-
tion hose port.
1. Unlock and remove the suction head.
2. Attach dust bag (special accessories).
Illustration N
3. Pull the dust bag (special accessories) over the con-
tainer.
4. Fit and lock the suction head.
Height adjustment of the floor nozzle
1. Turn the adjustment screw clockwise: High position
of the floor nozzle
2. Turn the adjustment screw anti-clockwise: Low po-
sition of the floor nozzle
The suction hose is equipped with the clip 2.0 connec-
tion. All accessory parts with nominal width DN 40 and
a clip 2.0 connection can be connected.
Illustration O
DANGER
Danger of electric shock
Risk of injury and damage.
The socket is only intended for direct connection of the
disposal pump to the vacuum cleaner. Any other use of
the socket is prohibited.
Note
Operators must be informed of the applicable PRCD
system before use.
English
Clip connection
Operation