Switching on the device
Illustration P
Power button
1
Power off button / test button
2
Circuit breaker
3
Red indicator light
4
1. Plug in the device's mains plug.
2. Press the on switch; the red indicator light illumi-
nates. The circuit breaker is on standby.
3. Press the off switch/test button of the circuit breaker;
the red indicator light goes out. The circuit breaker
switches off.
4. Press the on switch; the red indicator light illumi-
nates. The circuit breaker is on standby.
5. Switch on the device at the turn switch.
6. Continuously dispose of large fluid amounts: Switch
on the disposal pump.
Adjusting the suction power
Note
With the aid of the suction control, the amount of water
sucked in (pump capacity of the suction turbine) can be
adjusted to the output of the disposal pump. This pre-
vents the suction turbine from constantly switching off
and on and ensures continuous suction.
1. Remove the angle piece from the suction hose.
Illustration Q
2. Install the suction control on the suction hose.
3. Connect the angle piece to the suction control.
Make sure that the clip ring is aligned as shown in
the illustration.
Illustration R
4. Regulate the suction power on the suction control
(3-stage).
Disposal and cleaning operation
1. Continuously dispose of liquids or perform cleaning.
Emptying the pre-filter
1. Unlock and remove the suction head.
2. Remove the cable clip of the disposal pump.
3. Pull the pre-filter over the suction hose port and re-
move it.
4. Empty the pre-filter.
5. When inserting the pre-filter, push it over the suction
hose port until it touches the container wall.
6. Insert the cable clip of the disposal pump.
7. Fit and lock the suction head.
Switching off the device
1. If necessary, switch off the disposal pump.
2. Switch off the device at the turn switch.
3. Press the off switch/test button of the circuit breaker;
the red indicator light goes out. The circuit breaker
switches off.
4. Pull out the device's mains plug.
Each time after use
1. Empty the container.
2. Vacuum off the inside and outside of the device and
clean with a moist cloth.
Folding the push handle in/out
1. Release the push handle lock and adjust the push
handle.
Storing the device
1. Store the suction hose and mains cable as shown in
the illustration.
Illustration S
2. Store the device in a dry room and secure it against
unauthorised use.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
ATTENTION
Improper transportation
Risk of damage
Protect the mains plug of the disposal pump from dam-
age, as it reaches down to the ground when unplugged.
1. Remove the suction hose with floor nozzle from the
support. Carry the device by the carrying handle and
the suction pipe, not by the push handle.
2. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.
Care and service
DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
Replacing the flat fold filter
1. Open the filter cover.
2. Remove the filter frame.
3. Take out the flat fold filter (special accessories).
4. Insert the flat fold filter (special accessories). During
insertion, ensure that the flat fold filter is flush on all
sides.
5. Insert the filter frame.
6. Close the filter cover until it audibly latches into
place.
Change the candle filter
1. Open the filter cover.
2. Take out the candle filter (special accessories).
3. Insert the new candle filter (special accessories).
4. Close the filter cover until it audibly latches into
place.
Replacing the coarse dirt filter
1. Open the filter cover.
2. Remove the filter frame.
3. Replace the coarse dirt filter.
4. Insert the filter frame.
5. Close the filter cover until it audibly latches into
place.
English
Transport
Storage
15