Sabo 47-PRO E VARIO Manual Del Operador página 57

EN
– After cleaning or replacement, insert the filter insert (2) into the air filter
plate (1).
The material must lie flat on all sides without any creasing or folds W1.
– Insert the air filter correctly into the motor unit.
– Press the locking switch on the air filter and turn it clockwise according to the
symbol (2) to lock the air filter in place W.
In the case of unfavourable operation conditions (severe formation of dust),
cleaning is required after every mowing job. Replace the filter insert annually
or every 100 operating hours.
(For filter insert order no., see chapter "Original spare parts and
accessories")
21 TROUBLESHOOTING
Faults Possible causes
Start routine not performed
Motor does not
correctly
start
Battery not charged
Battery not functional or
cannot be charged
Cutting height set too low
(when the grass is too high,
this prevents the motor
from starting up)
Too much grass waste in
the housing or ejection
channel
Air filter soiled
Bowden cable elongated
Cutting height too low
Motor switches off
during mowing
Battery pack is drained
Too much grass waste in
the housing or ejection
channel
The cutter bar is blunt
Motor power
decreasing
Remedy
Press the on/off button on
the motor unit to switch on
standby mode.
Press and hold the button on
the top bar within
120 seconds.
Turn over the safety control
bar.
The blade motor and blade
start up.
The button (2) can then be
released while the safety
control bar must be kept in
that position so that the blade
continues to run.
Once the device is in standby
mode (step 1), steps 2 and 3
are sufficient for restarting
the blade motor.
Charge the battery (see the
separate operating
instructions for the charger).
Replace the battery.
Set a higher cutting height I.
Tilt the machine when
starting.
Clean grass out of the cutting
space / ejection channel,
keep the gap between the
fan and housing clean
(remove the battery/batteries
first N2 !).
Clean or replace the air filter
insert W + W1.
Have it checked by an
authorised workshop and
adjusted if necessary.
Have it checked by an
authorised workshop.
Set a higher cutting height I.
Charge the battery (see the
separate operating
instructions for the charger).
Clean grass out of the cutting
space / ejection channel,
keep the gap between the
fan and housing clean
(remove the battery/batteries
first N2 !).
Have it resharpened and
balanced by an authorised
workshop Q.
15
Battery voltage low
Too much grass waste in
the housing or ejection
channel
Air filter soiled
Autodrive control bar
Mower does not
run not pulled
Speed setting was made
while the motor was not
running
Belt has dropped off
Speed setting was made
Travel speed
while the motor was not
cannot be adjusted
running
Belt has dropped off
Extreme vibration
The cutter bar is blunt
Poor cutting,
lawn turns yellow
Cutting height too low
Motor speed too low
Excessive mowing speed
Mower paths
overlap sufficiently
Lawn matted
TurboSignal not observed
Ejection blocked
J + K
Cutting height too low and
grass too high.
Excessive mowing speed
Grass is wet
The cutter bar is blunt
The mulched grass
looks bad: lumps,
excessive amounts
of cut grass, coarse
Mulching rule not followed
cut
(cut max. 1/3 of grass
height; the grass height to
Charge the battery (see the
separate operating
instructions for the charger).
Clean grass out of the cutting
space / ejection channel,
keep the gap between the
fan and housing clean
(remove the battery/batteries
first N2 !).
Clean or replace the air filter
insert W + W1.
Pull up the autodrive control
bar G.
With the motor running, turn
the speed setting to the
highest setting and then, also
with the motor running, set it
to the lowest level.
The speed may only be
adjusted while the motor is
running to prevent any
damage!
Have it checked by an
authorised workshop.
Have it checked by an
authorised workshop.
With the motor running, turn
the speed setting to the
highest setting and then, also
with the motor running, set it
to the lowest level.
The speed may only be
adjusted while the motor is
running to prevent any
damage!
Have it checked by an
authorised workshop.
Have it checked by an
authorised workshop.
Have it checked by an
authorised workshop.
Have it resharpened and
balanced by an authorised
workshop Q.
Set a higher cutting height I.
Switch from "ECO"
"TURBO" (see chapter
"CHANGING THE MOTOR
SPEED (SWITCHING
ENERGY-SAVING MODE
ON/OFF)")
Adapt mowing speed.
do not With high grass, the mowing
paths may possibly have to
overlap more.
A noticeable improvement
can be achieved by using
a scarifier.
Empty the collecting bag L.
Set a higher cutting height
Adapt mowing speed.
Let lawn dry.
Have it resharpened and
balanced by an authorised
workshop.
Set a higher cutting height I.
to
I.