Sabo 47-PRO E VARIO Manual Del Operador página 58

be cut must be less than
10 cm).
Excessive travel speed
Grass accumulation under
the mower
Mower paths
overlap sufficiently
Grass is wet
In case of faults and defects which have not been listed here, please contact the
nearest authorised workshop.
Repairs which require specialised knowledge should only be performed by a
qualified expert. Your authorised workshop will naturally also be glad to help if you
do not wish to perform the maintenance work described here yourself.
22 MOTOR UNIT FAULT INDICATOR (FIGURE A2)
Light signal Meaning
The motor unit is in good
Green LED lights
working order
up
The motor unit has
Orange LED lights
overheated
up
Battery pack is drained
Red LED flashes
Blade motor overloaded
Orange LED
flashes
Communication between
Red and green
battery and control board
LEDs flash
disrupted
alternately
23 TECHNICAL DATA
Motor
Motor
Motor speed ECO
TURBO
Motor power ECO
TURBO
Charger
See the separate operating instructions for the charger.
Permitted temperature range during charging
Battery
See the separate operating instructions for the battery.
Recommended temperature range for storage
Mower
47-PRO E VARIO
Adapt travel speed.
Set a higher cutting height I.
do not With high grass, the mowing
paths may possibly have to
overlap more.
Set a higher cutting height I.
Let lawn dry.
Fixing the fault
Not necessary.
Check and clean the air
filters W + W1.
Let the mower cool down.
Reduce the load and do not
use the motor unit when the
ambient temperature is high.
Let the mower cool down.
Charge the battery.
Clean grass from the cutting
space / ejection canal,
remove blockages (remove
battery/batteries first) N2 !).
Set a higher cutting height
When mowing on a slope:
reduce the travel speed or
switch off autodrive. Mow at
right angles to the slope, not
upwards.
Check that the battery is
positioned correctly, or that
the batteries are correctly
placed in the battery
compartment. Correct this if
necessary and restart the
motor.
Have it checked by an
authorised workshop.
56 V DC motor
2400 rpm
2800 rpm
1.7 kW
2.4 kW
+ 5 to + 40 °C
+ 10 to + 26 °C
Housing
Cutting width
Cutting heights
Height adjustable guide bar
Grass collector capacity
Travel speed
Weight Machine with empty collecting bag
Also with 2 x 56 V 12 Ah batteries
Length
Width
Height
Wheels front/rear
Bearing front
Bearing rear
Permitted temperature range during use
Permitted temperature range for storage
Maximum permitted humidity
54-PRO E VARIO
Housing
Cutting width
Cutting heights
I.
Height adjustable guide bar
Grass collector capacity
Travel speed
Weight Machine with empty collecting bag
Also with 2 x 56 V 12 Ah batteries
Length
Width
Height
Wheels front/rear
Bearing front
Bearing rear
Permitted temperature range during use
Permitted temperature range for storage
Maximum permitted humidity
Sound power level
47-PRO E VARIO
Sound power level;
measured according to DIN EN IEC 62841-4-3
Measuring inaccuracies; according to DIN EN ISO 4871
Guaranteed sound power level;
measured according to 2000/14/EC
54-PRO E VARIO
Sound power level;
measured according to DIN EN IEC 62841-4-3
Measuring inaccuracies; according to DIN EN ISO 4871
Guaranteed sound power level;
measured according to 2000/14/EC
16
Die-cast aluminium with
25, 28, 35, 45, 55, 70, 80
ECO
TURBO
Ø 210 mm / Ø 210 mm
Bronze slide bearing
70 %, non-condensing
Die-cast aluminium with
15, 30, 40, 50, 60, 70, 85,
ECO
TURBO
Ø 210 mm / Ø 210 mm
Bronze slide bearing
70 %, non-condensing
EN
steel core
470 mm
Single wheel,
mm
3 times
65 litres
2.3 – 3.9 km/h
2.7 – 4.5 km/h
45.5 kg
52.8 kg
1740 mm
510 mm
1075 mm
Needle bearing
0 to + 45 °C
- 5 to + 60 °C
steel core
540 mm
Single wheel,
95 mm
2-part
75 litres
2.3 – 4.1 km/h
2.7 – 4.8 km/h
52.5 kg
59.8 kg
1730 mm
600 mm
1050 mm
Needle bearing
0 to + 45 °C
- 5 to + 60 °C
L = 92.8 dB(A)
WA
1.4 dB
L = 94 dB(A)
wa
L = 94.3 dB(A)
WA
1.3 dB
L = 96 dB(A)
wa