Publicidad
Idiomas disponibles
Idiomas disponibles
–
Remove the battery/batteries from the battery compartment N2.
14 EMERGENCY STOPPING
Release the safety control bar and the autodrive control bar.
–
The blade motor stops and the blade comes to a standstill.
–
The autodrive motor stops and the mower stops.
ATTENTION
Ensure before every mowing job that the safety control bar motor stop and
the autodrive control bar work properly:
–
When the safety control bar is released, the blade must come to a
standstill within 3 seconds.
–
When the autodrive control bar is released, the autodrive must stop
immediately and the mower must come to a standstill.
If this is not the case, please consult your nearest authorised workshop.
15 AUTODRIVE
NOTE
If the battery charge is too low, then the blade motor automatically switches
off. Charge the battery or batteries in good time beforehand.
Operation of the rear wheel drive (figure E2)
The rear wheel drive is switched on and off using the drive control bar (1) on the
upper guide bar (2) while the motor is running:
-
Pull and hold the drive control bar = mower moves.
-
Release the drive control bar = mower stops (0 position).
The drive control bar must always be firmly pulled towards the top bar.
Inappropriate actuation leads to wear of the transmission.
NOTE
The rear wheels click when the mower is pushed forward.
Speed adjustment (figure H)
IMPORTANT
The speed may only be adjusted while the motor is running to prevent any
damage!
NOTE
Excessive mowing speed leads to an unclean cut pattern or collection result.
Always adjust the speed to the individual circumstances. For cutting longer
grass, a lower travel speed should be selected.
The travel speed is adjusted with the rotary knob on the left.
–
To adjust the speed, turn the knob in the desired direction to set the desired
travel speed. The arrow on the rotary knob indicates the travel speed.
–
"Hare" position = fast (max. speed).
–
"Tortoise" position = slow (min. speed).
16 GRASS COLLECTOR
Operation with grass collecting bag
WARNING
When operating the equipment with a grass collecting bag, the bag must be
completely assembled and in technically perfect condition.
IMPORTANT
Ensure that when handling the grass collecting bag, the chute (1) R1 is not
bent.
When using the lawn mower, ensure that the grass collecting bag is emptied in
good time. The TurboSignal on the grass collecting bag shows you the right time
to empty it.
TurboSignal (fill indicator of the grass collecting bag) (Figure J + K)
An indicator is placed on the top of the grass collecting bag to show whether the
grass collecting bag is empty or full:
-
When the grass collecting bag is empty and during mowing, the TurboSignal
inflates J.
-
When the grass collecting bag is full, the TurboSignal collapses; then
immediately stop mowing and empty the grass collecting bag K.
IMPORTANT
If the collecting bag fabric is very dirty, the TurboSignal does not inflate - you
should clean the fabric immediately. The grass collecting bag will only collect
grass properly if air can pass through it freely.
IMPORTANT
Safety information!
For explanation of symbols, see the table on
Do not clean the grass collecting bag with hot water!
Emptying the grass collecting bag (figure F + L)
–
Switch off the motor F, wait until the cutter bar comes to a standstill.
–
Lift the ejection flap.
–
Remove the full grass collecting bag from the mower by the carrying strap –
the ejection flap closes automatically.
–
Shake out the grass collecting bag thoroughly, holding it by the carrying strap
and the moulded handle on the bottom L.
Operation without grass collecting bag
WARNING
When mowing without grass collecting bag, the ejection flap on the mower
housing must always be closed (flap down).
17 MOWING
NOTE
If the battery charge is too low, then the blade motor automatically switches
off. Charge the battery or batteries in good time beforehand.
Using the machine on slopes
ATTENTION
The mower can be used on banks and slopes with a gradient of up to 48%
(26° angle).
For safety reasons, however, we urgently recommend you do not exploit this
theoretical performance potential to the full. Always make sure you have a
firm stance. Walk-behind lawn mowers should never be used for slopes with
a gradient in excess of 26% (15° angle of slope). Stability may be lost!
Checking operating safety
The lawn mower is fitted with an motor stop device.
Before every mowing job, make sure that the motor stop safety control bar is
working perfectly. When the safety control bar is released, the cutter bar must come
to a standstill within 3 seconds.
After release, the safety control bar must always return to the position shown in the
"Description of components" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the stopping time of the blade is longer, stop using the device and take it to an
authorised workshop.
Measuring the stopping time
After starting the blade motor, it rotates and a wind noise can be heard.
The stopping time corresponds to the duration of the wind noise after the motor
has been stopped; it can be measured with a stopwatch.
Machine safety and protective devices must not be manipulated or disabled.
The correct operation of the autodrive control bar must also be checked before
page 5
each mowing job. When the autodrive control bar is released, the autodrive must
stop immediately and the mower must come to a standstill. If this is not the case, it
must be checked immediately by an authorised workshop.
Make sure that all protective devices have been attached properly and are not
damaged.
To avoid any risk, always check the condition and firm seating of the blade before
each mowing job. The blade fastening screw must always be tightened by an
authorised workshop. If the blade screw is tightened excessively or insufficiently,
blade fastening and cutter bar may be damaged or get loose, which can lead to
serious injuries. A worn or damaged blade must imperatively be replaced (see
chapter "Maintenance of the cutter bar").
Check fan, blade fastening and fan housing for wear and a tight fit every 10
operating hours. Also check device screws and nuts for a firm fit and re-tighten, if
necessary.
If the mower becomes blocked e.g. by colliding with an obstacle, have an
authorised workshop check whether any parts of the mower are damaged or
deformed. Always have any necessary repairs done by an authorised workshop
too.
If the machine starts to vibrate unusually heavily or to make unusual noises, please
have it checked immediately by an authorised workshop.
Time restrictions
In Germany, the time for the operation of lawn mowers is regulated in the "32nd
Ordinance for the Implementation of the Federal Immissions Act (32. BImSch-V)".
In addition, regional restrictions are possible (e.g. to observe the afternoon quiet
hours); related information is available from the competent municipal authority.
12
EN
Safety information!
For explanation of symbols, see the table on
page 5
Publicidad
