Troubleshooting - Teac LPR550USB Manual Del Usuario

If you experience any problems with the unit, please take a moment
to look through this chart and see if you can solve the problem
yourself before you call your dealer .
General
No power.
e Check the connection to the AC power source . Check and
make sure the AC source is not a switched outlet and if it is, the
switch is turned on . Make sure there is power to the AC outlet by
plugging another item such as a lamp or fan .
No sound.
e Adjust the volume .
The sound is noisy.
e The unit is too close to a TV set or similar appliances .
Relocate the unit further away from them, or turn the other
appliances off .
Remote control does not work.
e Press the POWER switch of the main unit to turn it ON .
e If the batteries are dead, change the batteries .
e Use the remote control unit within the (5m) range and pointed at
the front panel .
e Clear obstacles that are between the remote control unit and the
main unit .
e If a strong light is near the unit, turn it off .
CD Recorder
Will not play.
e Load a disc with the playback side facing down .
e If the disc is dirty, clean the surface of the disc .
e A blank disc has been loaded . Load a prerecorded disc .
e Depending on the disc, etc . it may not be possible to playback
CD-R/CD-RW discs . Try again with another disc .
Sound skips.
e Place the unit on a stable surface to avoid vibration and shock .
e If the disc is dirty, clean the surface of the disc .
e Do not use scratched, damaged or warped discs .
Recording is not possible.
e A playback-only disc or finalized disc has been loaded . Use a
recordable disc .
e The disc does not have a recordable area . Use another disc .
e The recording level is too low . Adjust the recording level .
e The recording does not start if only the RECORD button is
pressed . Always press the PLAY/PAUSE button (y/J) to start the
recording .
Tuner
Cannot listen to any station, or signal is too weak.
e Tune in the station properly .
e If a TV is near the unit, turn it off .
e Rotate the unit or antenna wire for the best reception position .

Troubleshooting

Turntable
Will not play.
e Loosen the transportation screw, and remove the stylus guard .
(The stylus guard is a plastic cover that protects the stylus during
transportation . Failing to remove this guard will not allow the
needle to contact the groove of the record and no sound will be
heard . )
Sound is noisy or strange.
e If the stylus is worn-out, change the stylus .
e Select the correct playback speed .
Sound skips.
e Place the unit on a stable surface to avoid vibration and shock .
Make sure the unit is level both front to back and side to side .
e Clean the surface of the record .
e Do not use scratched, damaged or warped records .
Cassette tape
The unit does not work even after operation buttons are
pressed.
e Confirm that a cassette tape has been set . If not, set a cassette
tape .
e Insert the cassette tape correctly .
Sound quality is poor.
e Clean the head .
e If the head is magnetized, demagnetize it with a head eraser .
e Set the TAPE switch according to the cassette tape used .
If normal operation cannot be obtained, unplug the power
cord from the outlet and plug it again.
Beware of condensation
When the unit (or a record/disc) is moved from a cold to a warm
place, or used after a sudden temperature change, there is the
danger of condensation; vapor in the air could condense on
the internal mechanism, making correct operation erratic or
impossible . To prevent this, or if this occurs, leave the unit for one
or two hours with the power turned on . The unit will stabilize at
the temperature of its surroundings .
Maintenance
Always keep the turntable clean .
If the surface of the unit gets dirty, wipe with a soft cloth or use
a diluted mild liquid soap . Be sure to remove any excess liquid
completely . Do not use thinner, benzine or alcohol as they may
damage the surface of the unit . Allow the surface of the unit to dry
completely before using .
33