Technical Data; Dimensions, Weights, Ambient Conditions; Supply Voltage (External); Outputs - Balluff BTL5-A -M -B-NEX-S32 Serie Manual De Instrucciones

BTL5-A/C/E/G1_-M_ _ _ _-B/Z-NEX-S32/KA_ _
Micropulse Linear Transducer - Rod Style
12

Technical Data

Typical values at DC 24 V, room temperature and BTL with nominal length of 500 mm. Ready for operation at once,
full accuracy after warm-up. With magnet BTL-P-1013-4R, BTL-P-1013-4S or BTL-P-1012-4R:
Repeatability
Voltage 0.3 mV
Current 0.6 µA
Minimum 0.05 mm
Sampling rate f = 2 kHz
Standard
Non-linearity
Nom. length < 500 mm > 500 mm
in µm ±100 ±0.02 % FS
Temperature coefficient
Voltage output:
[150 µV/K + (5 ppm/K * P * V/NL)] * ∆T
Current output:
[0,6 µA/K + (10 ppm/K * P * I/NL)] * ∆T
V = output voltage range in [V]
I = output current range in [mA]
NL = nominal length in [mm]
∆T = temperature coefficient in [K]
P = magnet position in [mm]
Shock 100 g/6 ms
per IEC 60068-2-27 1
Continuous shock 100 g/2 ms
1
per IEC 60068-2-29
Vibration 12 g, 10 to 2000 Hz
per IEC 60068-2-6 1
(take care to avoid inherent reso-
nances of protective tube)
Pressure up to 600 bar
when installed in a
hydraulic cylinder
1 Individual specifications as per
Balluff factory standard
12.1 Dimensions, weights,
ambient conditions
Nominal length < 4000 mm
➥ ➥ ➥ ➥ ➥ Fig. 3-2
Dimensions
Weight approx. 2 kg/m
Housing anodized aluminum
Pressure tube Stainless steel 1.4571
diameter 10.2 mm
wall thickness 2 mm
e-modulus approx. 200 kN/mm
Mounting thread M18×1.5 or
3/4"-16UNF
Operating temp. –20 °C to +60 °C
The CE Mark verifies that our
products meet the requirements
of EC Directive.
14
english
Humidity < 90 %, non-dewing
Protection rating
per IEC 60529 IP 67
with connector attached

12.2 Supply voltage (external)

Regulated supply voltage
BTL5-_1_-... DC 20 to 28 V
Ripple < 0.5 V
Current draw < 150 mA
Inrush < 3 A/0.5 ms
Polarity reversal protection built-in
Overvoltage protection
Transzorb diodes
Electric strength
GND to housing 500 V

12.3 Outputs

BTL5-A...
Output voltage 0...10/10...0 V
Load current < 5 mA
Ripple < 5 mV
BTL5-G...
Output voltage –10...10/10... –10 V
Load current < 5 mA
Ripple < 5 mV
BTL5-C...
Output current 0...20/20...0 mA
Load resistance < 500 Ohm
BTL5-E...
Output current 4...20/20...4 mA
Load resistance < 500 Ohm
The CE Mark verifies
that our products meet
the requirements of the
current EMC Directive
2
as well as the ATEX Directive.
Compliance is confirmed with the
enclosed CE declaration of conformity.
The transducer meets the requirements
of the following product standard:
EN 61326-2-3 (noise immunity
and emission)

12.4 Connection to controller

Analog interface:
With S32 connector for shielded
cable (max. length, see "Wiring"),
diameter 6 to 8 mm, or with integral
cable (5 m long)

12.5 Included in shipment

pp
Transducer
Calibration device ➥ ➥ ➥ ➥ ➥ Fig. 7-1

12.6 Magnets

(order separately)
Magnets BTL-P-1013-4R,
BTL-P-1013-4S, BTL-P-1012-4R
Dimensions
Weight
Housing
Operating temp. –40 °C to +85 °C
Included:
8 mm spacer
Material

12.7 Accessories (optional)

Connectors

12.8 Mounting nuts

(order separately)
Mounting nuts M18*1,5
BTL-A-FK01-E-M18X1,5
Mounting nuts 3/4"-16UNF
BTL-A-FK01-E-3/4"-16UNF
Emission tests:
RF Emission
EN 55011
Noise immunity tests:
Static electricity (ESD)
EN 61000-4-2
Electromagnetic fields (RFI)
EN 61000-4-3
Fast transients (Burst)
EN 61000-4-4
Surge
EN 61000-4-5
Line-induced noise induced by
high-frequency fields
EN 61000-4-6
Magnetic fields
EN 61000-4-8
Ignition Class "n"
➥ ➥ ➥ ➥ ➥ Fig. 3-2
➥ ➥ ➥ ➥ ➥ Fig. 3-4
approx. 10 g
anodized aluminum
POM (polyoxymethylene)
➥ ➥ ➥ ➥ ➥ Fig. 4-3
Severity level 3
Severity level 3
Severity level 3
Severity level 2
Severity level 3
Severity level 4