Multiplex CARGO Instrucciones De Montaje página 12

1. Examine your kit carefully!
MULTIPLEX models are subject to constant quality checks throughout the production process, and we sincerely hope that
you are happy with the contents of your kit. However, we would ask you to check all the parts before you start construction,
with reference to the parts list, as we cannot exchange components which you have already worked on. If you find any
part is not acceptable for any reason, we will readily correct or exchange it once we have examined it. Just send the
component to our Model Department. Please be sure to include a brief description of the fault.
We are constantly working on improving our models, and for this reason we must reserve the right to change the kit contents
in terms of shape or dimensions of parts, technology, materials and fittings, without prior notification. Please understand that
we cannot entertain claims against us if the kit contents do not agree in every respect with the instructions and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings in the normal sense of the word.
Building and operating them safely requires a certain level of technical competence and manual skill, together with
discipline and a responsible attitude at the flying field. Errors and carelessness in building and flying the model can
result in serious personal injury and damage to property. Since we, as manufacturers, have no control over the
construction, maintenance and operation of our products, we are obliged to take this opportunity to point out these
hazards.
Additional items required:
Radio control components:
MULTIPLEX MINI 9 receiver, 35 MHz-A / 40 MHz
MULTIPLEX MS-X2 servo (2 x required)
MULTIPLEX MS-X3 servo (2 x required)
MULTIPLEX PROFI 3BB FET servo
MULTIPLEX MULTIcont 40/16 BEC/EMF
MULTIPLEX separation filter (4 x required) Elevator / rudder / 2 x aileron
MULTIPLEX 30 cm extension lead (2 x required) 2 x aileron
MULTIPLEX 60 cm extension lead (2 x required) Elevator / rudder
or MULTIPLEX UNI cable set (2 x required) as low-cost alternative
to separation filter leads and 30 / 60 cm extension leads.
Flight batteries:
MULTIPLEX 7/1700 flight pack
MULTIPLEX 7/2000 flight pack
Geared motor set (recommended option):
The kit includes direct-drive motors and propellers. If you wish to convert to geared power plants, the same motors
can be used; you just install gearboxes and propellers from the MULTIPLEX 400L gearbox set incl. propellers (2 x
required for 4 motors)
Battery charger:
MULTIPLEX PICO AUTO-charger for rapid-charging transmitter and flight batteries 9 2526.
Adhesives:
MULTIPLEX 5-minute epoxy in dispenser (200 g resin + 200 g hardener = 400 g)
MULTIPLEX ZACKI 5 g (cyano-acrylate)
White glue, e.g. Henkel PONAL EXPRESS
Tools:
Scissors, combination pliers, balsa knife, screwdriver (slot-head, cross-point), round file,hacksaw blade,2 mm Ø drill.
Specification Wingspan
Fuselage length
Wing area (FAI) approx.
Weight min. approx.
Wing loading min. approx.
Wing section
Tailplane section
Controls
Important note
For all joints involving the styrofoam components it is essential that you avoid the use of solvent-based adhesives,
and standard instant or cyano-acrylate glue ("cyano", or "CA") in particular. These materials will melt and destroy a
large volume of foam, and the component will be completely ruined. Use solvent-free adhesives, such as 5-minute
epoxy or white glue.
12
Building Instrictions
Function
Elevator / rudder
2 x aileron
Loading bay flaps
Motor speed
1600 mm
1208 mm
45 dm²
2000 g
45 g/dm²
MPX 3.7-14
NACA 0010 / 0009
Elevator, rudder, aileron, motors, auxiliary functions
(e.g. loading bay doors, camera etc.)
GB
# 21 4073
Order No. Connector
5 5959 / 5 5961 UNI
6 5140 UNI
6 5135 UNI
6 5171 UNI
7 2253 UNI / HC
8 5035 UNI
8 5031 UNI
8 5032 UNI
8 5253 UNI
15 5646 HC
15 5529 HC
33 2693
60 2740
59 2700
Not in MPX range