NAMES AND FUNCTIONS OF PARTS
NAMES AND FUNCTIONS OF PARTS
CONNECTION PANEL
1
POWER
AC IN
18
1
POWER switch
2
PHONO input connectors
RCA type phono level (MM cartridge) input connectors.
Do not use for inputting line level signals.
3
DVD/LINE input connectors
RCA type line level audio input connectors.
Use to connect a DJ/VJ DVD player or DJ CD player or other line
level output component.
4
Signal ground terminal (SIGNAL GND)
Connect the ground wire from an analog turntable.
This is not a safety ground terminal.
5
CONTROL connector
Connect the Ø 3.5 mm mini phone plug of the control cable from
a DJ/VJ DVD player or DJ CD player.
When this is done, this mixer's fader controls can be used to
perform start and back-cue functions on the connected DJ/VJ DVD
player or DJ CD player.
6
LINE input connectors
RCA type line level audio input connectors.
Use to connect a cassette deck or other line level output
component.
7
DVD input connectors
RCA type line level audio input connectors.
Use to connect a DJ/VJ DVD player or DJ CD player or other line
level output component.
8
Audio master output 1 connectors (MASTER OUT 1)
XLR type (male) balanced output.
• When using a cord with RCA-type plug, users are recommended
to connect the plug directly to the MASTER OUT 2 connectors
without using an XLR/RCA converter plug.
When a conversion plug is used, the signal GND may become
unstable, in rare cases resulting in the production of noise.
9
Audio master output attenuator selector (MASTER ATT.)
Attenuates the output level of the audio master 1 and audio master
2.
Attenuation level can be selected as 0 dB, –3 dB, or –6 dB.
10 Audio master output 2 connectors (MASTER OUT 2)
RCA-type unbalanced output.
6
En
2
3 4
5
6 7
5
4
3
AUDIO OUT
SIGNAL GND
PHONO
DVD/LINE
LINE
DVD
MASTER OUT 1
R
L
L
CONTROL
CONTROL
R
R
OFF
ON
SYNC
SYNC
DIGITAL
OUT
OUT
14 15 16
IN
VIDEO OUT
DVD
DVD
S-VIDEO
S-VIDEO
VIDEO
VIDEO
19
19
8
9
10 11
12
1 GND 2 HOT
MASTER
REC
OUT
BOOTH
OUT 2
L
3 COLD
MONITOR
(TRS)
MASTER
L
R
L
ATT.
-3 dB
-6 dB
0 dB
R
DIGITAL OUT
17
15
fs (Hz)
48 k
96 k
MASTER
MONITOR
COMPONENT
COMPOSITE
Y
C
B
C
R
S-VIDEO
S-VIDEO
20
21
11 Recording output connectors (REC OUT)
RCA type output connectors for recording.
12 BOOTH MONITOR output jacks (TRS)
Ø 6.3 mm phone-type booth monitor output jacks.
The sound level output at these connectors can be controlled by
the BOOTH MONITOR level dial, regardless of the setting of the
MASTER LEVEL dial. (Since the output is TRS, both balanced and
unbalanced outputs are supported.)
13 Microphone 2 input jack (MIC 2)
Connect microphones equipped with phone-type plug.
14 Sync signal output connector (SYNC OUT)
Outputs video sync signal.
When connecting a Pioneer DJ/VJ DVD player (sold separately),
the sync signal helps suppress any lag between video and audio
signals.
15 Digital input connector (DIGITAL IN)
RCA-type digital coaxial input connector. Connect to the digital
coaxial output connector from a DJ/VJ DVD player or DJ CD player.
• If the sampling frequency of the output signal changes, the
sound may be interrupted briefly.
16 Sampling frequency selector switch (fs 48 k/96 k)
Use to set the sampling frequency of the digital output to 96 kHz/
24-bit format or 48 kHz/24-bit format.
Turn power off before changing this switch position.
17 Digital output connector (DIGITAL OUT)
RCA type digital coaxial output connector.
Master audio digital output.
18 Power inlet (AC IN)
Use the furnished power cable to connect to a household AC
outlet.
19 Video input connectors (DVD, VIDEO, S-VIDEO)
Composite and S-VIDEO type video input connectors.
20 Video master output connectors
(MASTER: COMPONENT, COMPOSITE, S-VIDEO)
Component, composite, and S-VIDEO type video output
connectors.
21 Video monitor output connectors (MONITOR, S-VIDEO)
Composite and S-VIDEO type monitor video output connectors.
6 7
5
2
3 4 5
13
2
1
SIGNAL GND
LINE
DVD
PHONO
DVD/LINE
MIC2
L
L
CONTROL
CONTROL
R
R
SYNC
SYNC
DIGITAL
OUT
OUT
MIDI
14
IN
OUT
DVD
DVD
USB
S-VIDEO
S-VIDEO
VIDEO
VIDEO
19
19
22
23