Sanding Tool Safety - Triton TROS125 Instrucciones De Uso

General & Electrical Safety
• In the event of a malfunction or breakdown, grounding provides a path of least resistance
for the electric current to reduce the risk of electric shock. This tool is equipped with an
electric cord with an equipment-grounding conductor and a grounding plug.
• The plug must be plugged into a matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
• Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed
by a qualified electrician.
• Improper connection of the equipment-grounding conductor can result in a risk of electric
shock. The conductor with green insulation - with or without yellow stripes - is the
equipment-grounding conductor.
• If repair or replacement of the electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
• Check with a qualified electrician or service personnel if the grounding instructions are not
clear, or if in doubt as to whether the tool is properly grounded.
• Use only 3-wire extension cords with 3-prong grounding plugs and 3-pole receptacles that
accept the tool's plug.
• Repair or replace damaged or worn cord immediately.
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and
adjusting wrenches are removed from the tool before switching it on.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4. DON'T USE IN DANGEROUS ENVIRONMENTS. Don't use power tools in damp or wet
locations, or expose them to rain. Keep work area well illuminated.
5. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work area.
6. MAKE THE WORKSHOP CHILD-PROOF with padlocks, master switches, or by removing
starter keys.
7. DON'T FORCE THE TOOL. It will perform more efficiently and safely when working at the rate
for which it was designed.
8. USE THE CORRECT TOOL. Don't force the tool or attachment to perform a task for which it
was not designed.
9. USE THE CORRECT EXTENSION CORD. Make sure the extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage, resulting in loss
of power and overheating. The table below shows the correct size to use depending on
cord length and the nameplate ampere rating. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
10. WEAR CORRECT APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving parts. Non-slip footwear is recommended.
Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use a face or dust mask if the cutting operation is
dusty. Everyday eyeglasses only have impact-resistant lenses; they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work when practical. It is safer than using
hands and also it frees both hands to operate tool.
13. DON'T OVERREACH. Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing, and when changing accessories, such as blades,
bits, cutters etc.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in 'off' position
before plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for recommended
accessories. The use of incorrect accessories may create a risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool
is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions that may affect its operation. A guard
or other part that is damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of
the blade or cutter only.
21. NEVER LEAVE THE TOOL RUNNING UNATTENDED. SWITCH THE POWER OFF. Do not leave
the tool unattended until it comes to a complete stop.

Sanding Tool Safety

• Hold the power tool by insulated handles or gripping surfaces only, because the sanding
belt/sheet may contact its own cord. Cutting a 'live' wire may make exposed metal parts
of the power tool 'live' and could give the operator an electric shock.
• Use clamps or another practical way to secure the workpiece to a stable platform.
Holding the workpiece by hand or against the body makes it unstable and may lead to
loss of control.
• Recommendation that the tool always be supplied via a Residual Current Device with a
rated residual current of 30mA or less.
• If the replacement of the supply cord is necessary, this has to be done by the manufacturer
or his agent in order to avoid a safety hazard.
a) ALWAYS wear appropriate protective equipment, including a dust mask with a
minimum FFP2 rating, eye protection and ear defenders
b) Ensure all people in the vicinity of the work area are also equipped with suitable
personal protective equipment
c) Take special care when sanding some woods (such as beech, oak, mahogany and
teak). The dust produced is toxic and can cause extreme reactions
d) NEVER use to process any materials containing asbestos. Consult qualified professional,
if you are uncertain whether an object contains asbestos
e) DO NOT sand magnesium or alloys containing a high percentage of magnesium
f) Be aware of paint finishes or treatments that may have been applied to the material
that is being sanded. Many treatments can create dust that is toxic, or otherwise harmful.
If working on a building constructed prior to 1960, there is an increased chance of
encountering lead-based paints
g) The dust produced when sanding lead-based paints is particularly hazardous to
children, pregnant women, and people with high blood pressure. DO NOT allow these
people near to the work area, even if wearing appropriate personal protective equipment
h) Whenever possible, use a vacuum dust extraction system to control dust and waste
i) Be especially careful when using a machine for both wood and metal sanding.
Sparks from metal can easily ignite wood dust. ALWAYS clean your machine thoroughly
to reduce the risk of fire
j) Empty the dust bag or container (where applicable) frequently during use, before
taking breaks and after completion of sanding. Dust may be an explosion hazard. DO
NOT throw sanding dust into an open fire. Spontaneous combustion may occur when oil or
water particles come into contact with dust particles. Dispose of waste materials carefully
and in accordance with local laws and regulations.
k) Work surfaces and sandpaper can become very hot during use. If there is evidence of
burning (smoke or ash) from the work surface, stop and allow the material to cool. DO NOT
touch work surface or sandpaper until they have had time to cool
l) DO NOT touch the moving sandpaper
m) ALWAYS switch off before you put the sander down
n) DO NOT use for wet sanding. Liquids entering the motor housing can cause severe
electric shocks
o) ALWAYS unplug the sander from the mains power supply before changing or
replacing sandpaper
p) Even when this tool is used as prescribed it is not possible to eliminate all residual
risk factors. If you are in any doubt as to safe use of this tool, do not use it
WARNING!
GB
5