Specifications - Rotel RSP-1576MKII Manual De Instrucciones

28
No Video Output
• Make sure that the TV monitor is connected properly and check the
input assignments.
• Check the source input and TV output resolution are compatible. A 4K
source can only be sent to a 4K monitor.
• HDMI cables must be 5 meters or less in length.
• If watching 3D sources, make sure the display is 3D enabled.
Video and Audio do not match.
• Check that the proper video source is selected for each input.
• Check that the group delay (lip-sync) setting is not mis-adjusted.
Clicking or popping sounds when switching inputs
• The unit uses relay switching to preserve maximum sound quality. The
mechanical clicking of the relays is normal.
• Switching between HDMI sources may cause delays as HDMI two way
communications "handshake" must be established between the source
and display. The time required for the handshake varies depending
on the attached equipment.
Controls do not operate
• Make sure that fresh batteries are installed in the remote.
• Make sure that the IR sensor on the front panel is not blocked. Aim the
remote control at the sensor.
• Make sure the sensor is not receiving strong IR light (sunlight, halogen
lighting, etc.).
• Unplug the unit from the AC outlet, wait 30 seconds, and plug it
back to reset.
• Confirm the IR Codeset set in the remote control and RSP-1576MKII
are matched to either Codeset 1 or Codeset 2.
Use of the Made for Apple badge means that an accessory has been
designed to connect specifically to the Apple product(s) identified in the
badge and has been certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards
Apple, Apple TV, Apple Watch, iPad, iPad Air, iPad Pro, iPhone, and Lightning
are trademarks of Apple Inc., registered in the U.S. and other countries. tvOS
is a trademark of Apple Inc.

Specifications

Audio
Total Harmonic Distortion
Intermodulation Distortion (60 Hz : 7 kHz, 4:1)
Frequency Response
Signal to Noise Ratio (A-weighted)
Input Sensitivity/Impedance
Preamp Output Level
Channel Separation (at 10k Hz)
Digital Audio
Video
Input Resolutions
Output Resolution
Color Space Support
Deep Color Support
HDMI Inputs/Outputs
General
Power Consumption
Power Requirements (AC)
BTU
Dimension (W x H x D)
Front Panel Height
Weight
.
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
Rotel and the Rotel Hifi logo are registered trademarks of The Rotel Co., Ltd. Tokyo, Japan.
RSP-1576MKII Surround Sound Processor
Phono Input
Analog Bypass
Digital Input
Analog Bypass
Digital Input
Phono Level
Line Level
Balance Level
Line Level
0.0006% (Analog Bypass)
0.003% (Digital Input)
< 0.005%
20 Hz - 20k Hz, ± 0.5 dB
10 Hz - 100k Hz, ± 1 dB
20 Hz - 20k Hz, ± 0.5 dB
112 dB
112 dB
3.5 mV / 47k ohms
270 mV / 100k ohms
500 mV / 100k ohms
1.0 V
> 75 dB
LPCM (up to 192kHz, 24-bit)
Dolby ® Surround,
Dolby ® TrueHD,
Dolby ® ATMOS,
DTS-HD Master Audio,
DTS X
Dirac Live Full
480i/576i, 480p/576p, 720p,
1080i, 1080p, 1080p 24Hz,
3D, 4K, UHD, 4K 60Hz, 4K HDR10
480i/576i, 480p/576p, 720p
1080i, 1080p, 1080p 24Hz,
3D, 4K, UHD, 4K 60Hz, 4K HDR10
sRGB, YCbCr 4:2:2, YCbCr 4:4:4
24-bit, 30-bit, 36-bit
7 inputs supporting HDCP 2.2, HDMI2.0b
2 outputs supporting HDCP 2.2, HDMI2.0b
Audio Return Channel
60 watts
< 0.5 watt (standby)
120 volts, 60Hz
230 volts, 50Hz
114 BTU/h
431 x 144 x 348 mm
17 x 5 2 / x 13 5 / in
3 7
3U / 132.6 mm / 5 1 / in
4
8.8 kg / 19.4 lbs