18
Remote Control Overview
The RSP-1576MKII is supplied with an easy to use remote control RR-CX100.
The RR-CX100 can be configured to use IR codeset 1 or IR codeset 2 in case
the unit is conflicting with other Rotel models. Push and hold the TUNER
button and 1 (or TUNER and 2 for codeset 2) at the same time and hold for
approximately 5 seconds until the backlights on the remote control blink on
then off then release both buttons. This sets the remote control to use codeset
1 (or codeset 2 if TUNER and 2 are held). The System menu in the OSD
includes a configuration option to set the processor to either codeset 1 or
codeset 2. The factory default for the remote and processor is codeset 1.
The RR-CX100 can also control an attached Rotel CD player. The CD player
functions include Play, Stop, Pause, Track Forward, Track Back, Fast Forward,
Fast Reverse. To activate these functions press the CD button on the remote.
If the CD is attached to the XLR source input, these functions can be activated
by pressing the XLR button. To change the CD player functions to operate
after pressing the XLR button press and hold the XLR and 1 button for 5
seconds until the backlight LEDs blink twice times then release. To disable
XLR sending the CD control functions press and hold the XLR and 0 button
for 5 seconds until the backlight blinks.
The transport buttons will only operate for CD control after the CD or XLR
button is pressed on the remote. If a different input is selected from the
remote these buttons will no longer send the CD transport IR commands.
Overview of Buttons and Controls
This section provides a basic overview of the buttons and controls on the
front panel and the remote control. Detailed instructions on the use of these
buttons are provided in the more complete operating instructions in the
following sections.
STANDBY
and Power ON/OFF Buttons
1
The front-panel STANDBY button and the remote control ON/OFF button
activate or deactivate the unit. The rear panel master POWER switch must
be on the ON position for the remote standby function to operate.
VOLUME Knob and VOLUME UP/DOWN Buttons
The VOLUME UP/DOWN buttons on the remote and the large rotary control
on the front panel provide the master VOLUME control, adjusting the output
level of all channels simultaneously including mute and volume level 1 to 96.
DISPLAY (DISP) Button
0B
Push this button to toggle through device status on the VFD and TV.
SETUP Button
H
Navigating and ENTER Buttons
The SETUP button displays the OSD setup screen on the HDMI OSD enabled
output. Push the SETUP button again to deactivate this menu. Use the
navigation buttons Up/Down/Left/Right and ENTER on the remote control
to access the various menus.
MUTE Button
-F
Push the MUTE button once to turn the sound off. An indication appears in
the front panel and on-screen display. Press the button again to restore the
previous volume level.
A
=D
I
RSP-1576MKII Surround Sound Processor
Input Buttons
4qM
The input source can be changed by pressing the desired source input
buttons on the front panel or remote control.
SUR+ Buttons
9B
The SUR+ buttons on the remote control or front panel will display surround
mode information of currently selected source. The default DSP mode can
be configured in the Setup menu for each source. Press the SUR+ button
repeatedly to toggle through the available DSP modes.
DSP processing options vary depending on the selected source input type.
Not all DSP options are available in analog or digital input modes.
Other buttons on the remote can directly access specific DSP modes.
2CH: Changes the audio mode to STEREO, DOWN MIX.
BYPASS: Bypass all DSP processing.
PLCM: Selects Dolby ATMOS surround mode.
DTS Dialog
I
To change DSP processing for alternate DTS Dialog options to press the
I
Up/Down arrow buttons
on the remote control. Options for DTS Dialog
include DTS Dialog 0, DTS Dialog 3, DTS Dialog 6. This function is only
available when the DSP is engaged and is not active in Analog Bypass
mode. Settings are temporary and not saved after a power cycle. Default
is DTS Dialog 0.
Dynamic Range Control (DRC)
DRC allows changes to the Dynamic Range of the audio. This function can
be useful when there is a desire to reduce the energy of the audio output
such as watching a movie at night . To select the different DRC modes press
I
the Right/Left arrow buttons
settings to select the desired option. Options include DRC Off, DRC 66%,
DRC Auto and DRC Night. Different options produce differing Dynamic
Range controls. Select the option that best suits your desired Dynamic Range.
This function is only available when the DSP is engaged and not active in
Analog Bypass mode. Settings are temporary and not saved after a power
cycle. Default is DRC Off.
Playback Control buttons
L
These buttons provide basic control functions for iPod AUDIO playback.
The control buttons can also control Rotel CD players. For more information
how to configure CD controls see the REMOTE CONTROL OVERVIEW
section of the manual. Supported functions include Play, Stop, Pause, Next
Track, Previous Track.
DIM Button
J
Use this button to dim the front panel display.
J
Adjustment made using the
after power off.
SUB, CTR, REAR Buttons
B
These buttons can access the speaker setting and adjust the output level for
speakers in the system. Use the Up and Down arrow buttons on the remote
control to change values. This is only a temporary change. To make permanent
adjustments, please access the SPEAKER LEVEL SETUP menu from the OSD.
MEM Button
E
This button does not operate with the RSP-1576MKII and is used only to
control a Rotel tuner product for preset memory control.
I
on the remote control to cycle through DRC
button is temporary only and not saved