Video Setup; Troubleshooting - Rotel RSP-1576MKII Manual De Instrucciones

the RSP-1576MKII will enter Signal Sense Standby Mode. When in
Signal Sense Standby Mode and the RSP-1576MKII detects audio on
Signal Sense Input, the unit will automatically power on. To disable this
function, select the DISABLE option which is the factory default setting.
NOTE: When the RSP-1576MKII enters standby mode via the remote
control, the Signal Sense function will not operate until the unit detects
the audio has stopped for the minimum 10 minute time-out period. This
prevents the unit from immediately powering back on if there is still
active audio playing.
NOTE: When the SIGNAL SENSE INPUT function is activated, the
RSP-1576MKII will consume additional power in signal sense standby
mode.
NOTE: Due to local power consumption regulations the Signal Sense
function is not available in all markets.
NETWORK CONFIGURATION: Sets the network configuration for the unit. In
most systems, set the IP ADDRESS MODE to DHCP. This setting will allow
your router to assign an IP address to the RSP-1576MKII automatically. If
your network uses fixed IP addresses, set the IP ADDRESS MODE to Static. A
fixed or STATIC IP address requires manually entering the IP Address, Subnet
Mask, Gateway, and DNS in the IP ADDRESS CONFIGURATION sub menu.
NETWORK CONFIGURATION
IP ADDRESS MODE
RENEW DHCP IP ADDRESS
VIEW NETWORK SETTINGS
TEST NETWORK CONNECTION
BACK
SOFTWARE INFORMATION: Displays the current software installed in the
unit. It shows the MAIN, DSP and STANDBY software versions. There is also
an option to check for software updates. This feature lets the unit search
for software updates on the Internet. The network needs to be properly
configured. Alternatively, you can load the software through the front USB
socket. For more information on the software update process please contact
your authorized Rotel dealer.
RESTORE FACTORY DEFAULT: This option sets the unit back to the original
setting as when it left the factory. All user settings will be erased.
NOTE: Use caution when resetting the RSP-1576MKII to factory defaults
as all user configured options will be erased and reset to original
factory settings.

Video Setup

VIDEO SETUP
STANDBY VIDEO SOURCE
FAST AUDIO SYNC
OSD FORMAT
BACK
DHCP
DISABLE
DISABLE
480P
The VIDEO SETUP menu provides configuration of the HDMI outputs. See
the HDMI INPUTS & OUTPUTS section of this manual for details on HDMI
connections.
STANDBY VIDEO SOURCE: Options are "DISABLE", "HDMI 1-6", "HDMI
FRONT", or "LAST". This allows the selected HDMI source input to pass-
through the RSP-1576MKII while in standby mode. Audio and video are
passed directly to the attached TV or display.
NOTE: When the Standby Video Source is enabled the RSP-1576MKII
will consume additional power when in standby mode.
NOTE: Signal Sense power control is disabled with STANDBY VIDEO
SOURCE is enabled.
FAST AUDIO SYNC: This function allows the HDMI audio to sync more quickly
with the RSP-1576MKII. Only 1 input can be selected for this function.
NOTE: Some source devices do not provide the timing requirements to
allow this function to work properly and could result in static noise before
the audio is heard.
OSD FORMAT: The HDMI On Screen Display output resolution can be
changed from 480P to 576P. The default value is 480P.
Press the BACK button or select "BACK" on the OSD to exit the VIDEO
SETUP Menu and return to the main menu.

Troubleshooting

Most difficulties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the problem
area, check the control settings, determine the cause of the fault and make
the necessary changes. If you are unable to get sound from the unit, refer
to the suggestions for the following conditions:
The unit does not turn on
• Make sure the power cord is plugged into the rear panel and a AC outlet.
• Make sure the rear panel POWER switch is in the ON position.
No sound from any input
• Make sure that MUTING is off and VOLUME is turned up.
• Make sure source inputs are connected and configured correctly.
No sound from digital sources
• Make sure that digital input connector is assigned to the proper source
input and that the source input is configured to use the digital input
rather than an analog input.
• Check the configuration of the digital input source player to ensure
that the digital output is activated.
No sound from some speakers
• Check all power amp and speaker connections.
• Check Speaker Configuration settings in the Setup menus.
27