Installation - Rock Shox Judy C Manual Del Propietário

Installation Instructions for Judy C, XC, and 100
It is extremely important that your RockShox fork is installed correctly by a qualified technician with proper
tools. Improperly installed forks are extremely dangerous and can result in severe and/or fatal injuries.
1. Remove the existing fork and lower headset race from the bicycle. Measure the length of the fork
steerer tube diameter against the length of the RockShox steerer. The RockShox steerer tube may need
cutting to the proper length. On threadless steerers (Aheadset design), make sure there is sufficient
length to properly clamp the stem (refer to stem manufacturer's instructions). Remember to measure
twice and cut once.
I : D
MPORTANT O NOT ADD THREADS TO
- . R
ONE TIME PRESS FIT
(
HEADSET TYPE THREADED OR THREADLESS
RESULT IN LOSS OF CONTROL OF THE BICYCLE WITH POSSIBLE SERIOUS AND
2. Install the headset race (26.4 mm for 1" steerers, 29.9mm for 1-1/8" steerers) firmly against the top of
the fork crown. Install the fork assembly on the bike. Make sure there are sufficient threads to properly
lock the headset in place. On threadless steerers (Aheadset design), make sure there is sufficient length
to properly clamp the stem (refer to stem manufacturer's instructions). Adjust the headset so you feel
no play or drag.
3. Install the brakes according to the manufacturer's instructions and adjust brake pads properly. Use the
fork only with cantilever-type brakes mounted to the existing mounting posts or disc style brakes
mounted through the mounting holes provided.
4. On threaded steerers, insert stem to a minimum depth according to CPSC and JIS standards. The stem must be
inserted to a minimum engaging length not less than 2.5 times the stem diameter from the lowest end of the
stem, not the wedge (see Fig. 1).
5. Fit a brake cable to the RockShox fork brace mount on hangered forks. Do not
route the cable through the stem or any other mounts or cable stops! The cable
should make a direct route from the brake lever to the RockShox fork brace
mount and be able to freely move up and down with the suspension movement.
It may be necessary to install a whole new cable. Forks with hangerless style
braces were designed for V-type, hydraulic cantilever brakes or disc style brakes
mounted to the tabs provided. Do not use any cantilever brake other than those
intended by the brake manufacturer to work with a hangerless brace.
N : T
OTE HE DISTANCE FROM THE TOP OF THE BRAKE CABLE HANGER TO THE BOTTOM OF THE BRACE CABLE
HOUSING STOP MUST BE A MINIMUM OF
BRAKE CABLE COULD RESULT IN LOSS OF CONTROL OF THE BICYCLE WITH POSSIBLE SERIOUS AND
6. Adjust the front wheel quick release to clear the dropout's counter bore. The quick release nut must be
tightened after the wheel is properly seated into the dropouts counter bore. Make sure four or more
threads are engaged in the quick release nut when it is closed. Orient the quick release lever in front of
and parallel to the lower tube in the locked position.
7. Keep in mind tire clearance as you choose tires. Maximum tire size is 2.2" wide or 335mm radius. Be
sure to check this radius whenever you change tires. To do this, remove the spring stack (per instructions
on following pages), and compress fork completely to make sure at least 5 mm of clearance exists between
the top of the tire and the bottom of the crown. Exceeding this maximum will cause the tire to jam
against the crown when the forks are fully compressed. The upper tubes must always be fully engaged in
the crown. The upper tubes, on clamp type crowns, must not extend above the crown more than 1mm.
PN 950-001770-01, R
R
OCK
EPLACEMENT OF THE ASSEMBLY MUST BE DONE TO CHANGE LENGTH
). DO NOT
12
MM WITH THE BRAKES APPLIED
B
EV
S . T
HOX STEERERS HE STEERER TUBE CROWN ASSEMBLY IS A
REMOVE OR REPLACE THE STEERER TUBE
,
DIAMETER
,
/ .
OR FATAL INJURIES
. A
N IMPROPERLY INSTALLED FRONT
/
OR FATAL INJURIES
,
OR
THIS COULD
Fig.1
.
P 7
AGE