Setting The Riving Knife; Changing The Saw Blade; Transport; Keeping Your Table Saw Safe And Secure - Parkside PTKS 1800 SE Instrucciones De Utilización Y De Seguridad

Sierra circular de mesa
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Operation
j
Slide the mitre guide
fig. G. Saw the workpiece in one operation.
j
Switch off the machine immediately if you are
not going to continue to use it.

Setting the riving knife

Q
WARNING!
The riving knife
the integrated safety devices and must always be
correctly installed. The distance between the outside
edge of the saw blade
must be between 3 and 5 mm (see Fig. I).
j
Turn the blade height adjustment wheel
raise the saw blade
saw blade
at 45° using the blade angle
4
adjustment thumb knob
guard
.
2
j
Remove the table insert
To do this, unscrew the two screws using a
cross-head screwdriver.
j
Unscrew the fittings on the cover plate
swing the plate away. To do this it is necessary
to set the saw blade
j
Loosen the screws and align the splitter
Retighten the screws.
j
Attach the cover plate
and the blade guard

Changing the saw blade

Q
WARNING!
Before you carry out any work
on the device always pull the mains plug out of the
mains socket.
WARNING!
Wear protective gloves when
replacing the saw blade
blade can cut or cause injury.
j
Wind the saw blade
justment wheel
14
the blade angle adjustment thumb knob
j
Take off the blade guard
j
Remove the table insert
the two screws using a cross-head screwdriver.
38 GB/MT
evenly forward, see
8
is one of
3
and the riving knife
4
14
fully and incline the
4
. Take off the blade
18
.
7
23
inclination back to 0°.
4
3
, the table insert
23
.
2
. Even a stationary saw
4
upwards using the ad-
4
and incline it by 45° using
18
.
2
. To do this, unscrew
7
j
Unscrew the fittings on cover plate
saw blade
j
Hold the saw blade
counter key
with the supplied combi-tool
24
and Fig. M. Remove the clamping flange
j
Remove the saw blade
j
Clean the clamping surfaces.
j
Place the new saw blade in position.
Only suitable saw blades are to be used.
See the sections "Technical information".
Take note of the direction of rotation and the
3
correctly installed position of the saw blade.
Saw blades must be mounted properly. Ensure
to
that they are balanced, rotate smoothly and
cannot come loose.
j
Put on the clamping flange
clamping screw
bi-tool
whilst holding it still with the counter
11
key
.
10
j
Attach the cover plate
and the blade guard
and

Transport

Q
.
j
When moving the table saw do it with another
person and hold the saw at the recesses in the
7
housing.
Keeping your table saw safe
Q
and secure
j
Prevent unauthorised people from gaining
access to your table saw.
j
Take care to see that no one can be injured by
your table saw.
j
Disconnect the table saw from the mains.
j
Disconnect the vacuum extraction device from
the table saw.
j
Align the saw blade
0° and set the cutting depth to the minimum.
j
.
Ensure that the bottom edge of the dust extrac-
tion cowl / blade guard
saw table
j
Attach the guide fence
to the saw table
8
and swing the plate away.
4
in position with the
4
and slacken the clamping screw
10
11
.
4
and attach the
25
. Tighten fully with the com-
24
, the table insert
23
.
2
to a blade angle of
4
lies fully on the
2
.
5
and the mitre guide
1
.
5
to the
23
, see Fig E
.
25
7

Publicidad

Tabla de contenido
loading

Tabla de contenido