Jacuzzi J-400 Manual De Instalacion Y Uso & Mantenimiento página 68

would like "Program B" to run for a heating cycle. Press the Up
or Down button (on the Quad Keypad) to scroll through and
change the days you would like the heating to activate. Press the
Left or Right button to turn "ON" (
that day.
PROGRAM B
Monday
Tuesday OFF
Wednesday OFF
Select
Thursday OFF
B
Friday OFF
Saturday OFF
Sunday OFF
2
Press to Save
Press the Splash button once to save settings.
Press button D to return to the submenu to continue program-
ming the start time and duration.
I
Once back to the "Program B" Main Menu, press the Down but-
ton on the Quad Keypad to select "Start Time". Press the Left
or Right button on the Quad Keypad to select the time you wi-
sh the spa to run. Press the Down button on the Quad keypad
to access the "Duration" setting.
PROGRAM B
Day Settings
Start Time 1PM Start Time
Select
Duration
B
Press to Save
2
Note: If you are using a standard 12-hour period, you will
see the hour displayed as "1PM." For the 24-hour period it will
read "1300."
I
Now you will need to adjust the "Duration" of the cycle. The
duration range is from 0 (OFF) to 6 hours. Press the Left or Ri-
ght button on the Quad Keypad to make your adjustment (s) in
increments of 1 hour.
PROGRAM B
Day Settings
Start Time
Select
Duration Duration
B OFF
Press to Save
2
Note: The default "Duration" is OFF.
Press the Splash button on the Quad Keypad to save your chan-
ges and return to the Heating Menu.
Press button D to exit the Heating Menu and return to the Set-
tings 1 Main Menu. If you have programmed both heating cycles
and the settings have been accepted, you will see the two pro-
gram icons next to word Heating on the display. If only one cy-
cle was programmed, there will only be one icon.
SETTINGS 1
Heating
A B
UV Light
0 Days
1
Filter
OFF
Press to
2
set filter or UV timer
) or "OFF" the heating for
68
Clean-Up "Blow-Out" Cycle
The clean-up cycle occurs once per day in all Heating modes at
12:00 (noon) for two minutes. This is not user programmable. Ea-
ch jets pump activates for one minute to circulate any water in
the plumbing unless a pump has just finished a 20 minute time
out, it will not automatically activate for the clean-up cycle. Be
aware, the factory programmed clean-up cycle cannot be can-
celed or altered!
I
Programming the CLEARRAY™ timer
Use the Quad Keypad down button to select "UV Light. " After the
"UV Light" selection is active, press the Splash button to acti-
vate the "UV timer".
SETTINGS 1
Heating
ENERGY EFFICIENT
UV Light
0 Days
1
Filter
OFF
Press to
2
set filter or UV timer
Press the Left button on the Quad Keypad to set the "UV timer"
to 365 days.
Note: The UV timer counts down by days not usage. The days
are store in memory if the power is interrupted.
3. When the timer expires, the "Bulb Expired!" message will ap-
pear on the Main Menu display. The UV bulb must be replaced
and the timer must be reset. Just follow the instructions above
to reset the UV timer.
Note: When the timer expires, the indicator light will turn red.
The bulb must be replaced and the timer reset.
I
Setting the Check Filter Reminder
Use the Quad Keypad down button to select Filter. After "Filter"
selection is active, press the Splash button to access the "set fil-
ter timer".
SETTINGS 1
Heating
ENERGY EFFICIENT
UV Light
0 Days
1
Filter
OFF
Press to
2
set filter or UV timer
Press the Left or Right button on the Quad Keypad to scroll the
number of days you would like the reminder to appear so the fil-
ters and polishing bag can be cleaned or replaced.
Press the Splash button to confirm and save your selection.
When the set time period expires, the "Please check filter!" mes-
sage will appear on the Main Menu display. The reminder must
be reset when the time allotted expires.
Note: The time range is from 10 to 365 days in increments of
10 days or you can elect to turn the feature "OFF."
SETTINGS 1
Heating
ENERGY EFFICIENT
UV Light
365 Days
1
Filter
OFF
2
SETTINGS 1
Heating
ENERGY EFFICIENT
UV Light
365 Days
1
Filter
0 Days
Press to
2
save settings