Zhermack ARIO 35 Manual Del Usuario página 26

Do not use inflammable, corrosive, alkaline or
toxic liquids to clean the equipment.
8.2 ROUTINE MAINTENANCE
Once the equipment has been cleaned (see paragraph
8.1), the operator must check for worn, damaged or loose
parts. If any such situations are detected, contact the
Authorised After-Sales Centre.
If any of the previously-described situations
should occur, it is prohibited to re-start the
EN
equipment before the problems have been
solved.
In particular, before moving away from the equipment,
the operator detecting problems of any nature must place
a sign on the it indicating that equipment maintenance is
in progress and that use is prohibited (EC-compliant signs
can be purchased from the relevant suppliers). Routine
maintenance, cleaning and correct equipment use are
essential factors in guaranteeing long-lasting equipment
performance and safety.
8.2 ROUTINE MAINTENANCE
Once the equipment has been cleaned (see paragraph
8.1), the operator must check for worn, damaged or loose
parts. If any such situations are detected, contact the
Authorised After-Sales Centre.
If any of the previously-described situations
should occur, it is prohibited to re-start the
equipment before the problems have been
solved.
In particular, before moving away from the equipment,
the operator detecting problems of any nature must place
a sign on the it indicating that equipment maintenance is
in progress and that use is prohibited (EC-compliant signs
can be purchased from the relevant suppliers). Routine
maintenance, cleaning and correct equipment use are
essential factors in guaranteeing long-lasting equipment
performance and safety.
8.3 EXTRAORDINARY MAINTENANCE
Extraordinary maintenance includes the repair of any
accidental breakage and the replacement of worn or
malfunctioning parts.
All electrical and mechanical interventions must
only be performed by a Zhermack-authorised
maintenance technician.
26
The reference figures can be found on pages 3, 4, 5 and 6 of this manual.
Any modification that alters equipment features
from a safety and risk-prevention point of view
can only be carried out by the Manufacturer who
will then certify conformity of the equipment
with safety standards. Therefore any modification
or maintenance intervention not considered in
this manual is to be considered prohibited. Any
modification, tampering or repair performed by
unauthorised staff along with the use of non-
original spare parts relieve the Manufacturer from
any liability. If the necessary maintenance
interventions are not considered in this Use and
Maintenance Manual, contact the Authorised
After-Sales Centre.
8.4 RE-START AFTER LONG PERIOD OF INACTIVITY
If the equipment is re-started after a particularly long
period of inactivity, operate as indicated in Chapter 6
regarding commissioning.
If the equipment functions anomalously, act as described
in Chapter 9 regarding "Diagnostics". if the problem should
persist or is not considered, contact the Authorised After-
Sales Centre immediately.
8.5 HOW TO REQUEST AFTER-SALES ASSISTANCE
Choose one of the following options to request after-sales
assistance:
1. contact the Authorised After-Sales Centre;
2. telephone Zhermack Customer Services at 800 856014
(Italy only) or +39-0425-597611 and proceed as
follows: give your personal information (e.g. address
and telephone number); give the data reported on the
machine rating plate (see paragraph 3.5); describe the
problem clearly;
3. fax all of the information stated in the previous point
and the correctly filled-in identification form (see
Attachment 10.2) to the following n° +39 0425 53596.
CHAPTER 9: TROUBLESHOOTING
9.1 GENERAL WARNINGS
If any of the anomalies described below should
occur, solve the problem, where allowed, with
respect to all instructions contained in this
manual. If the problem persists, contact the
Authorised After-Sales Centre.
9.2 TROUBLESHOOTING
DEFECT The micromotor stops unexpectedly
during operation.
CAUSE The fuse has blown.
REMEDY Replace the fuse with one with the same
characteristics.
If the problem persists, contact an Authorised
Service Centre.
ARIO 35