Rear Panel - Marantz ZS5300 Manual Del Usuario

Rear panel

1 2
AUDIO IN AUDIO IN AUDIO OUT AUDIO OUT
R R L L R R L L
1 1
2 2
3 3
z z Audio input terminal (AUDIO IN)
Connect the analog audio output from your audio device
(CD player, TV, DVD player, etc.). Up to 3 audio devices
can be connected.
x x Audio output terminal (AUDIO OUT)
These terminals are designed as an Audio pass through.
They can be used to when cascading one or two other
ZS5300s. Another example might be to share source
components with a dedicated home theater system etc.
c c Zone direct input terminal (ZONE DIRECT IN)
These terminals are only for their corresponding zone.
Connect the analog audio output terminals from your audio
device (CD player, TV, DVD player, etc.). Although up to 3
devices can be connected each to a different zone, the
device connected to "ZONE DIRECT 1" can be played
only in ZONE 1. The same applies to ZONE DIRECT 2
and ZONE DIRECT 3.
• You can construct a powerful & unique multi-zone
system by connecting the Marantz music server
(DH9300). ( P. 13)
v v Zone 3 pre output terminal (ZONE 3 PRE OUT)
These terminals are preamplifier output terminals for
Zone 3. These terminals can be connected with other
audio devices such as an external amplifier.
b b Remote control input / output terminal
(REMOTE CONTROL)
By connecting this unit to another Marantz audio component
using a System control cable, you can remotely operate the
components as a single system.
n n Speaker output terminal (SPEAKERS)
Connect speakers for each zone.
• Rating of speaker impedance: 6 ohm
3 4 5
ZONE 3 PRE OUT ZONE 3 PRE OUT
R R L L
ZONE DIRECT IN ZONE DIRECT IN
R R L L
STATUS OUT STATUS OUT REMOTE CONTROL REMOTE CONTROL ID ID
SELECTOR SELECTOR
ZONE ZONE 1 1 ZONE ZONE 3 3
IN IN
EXT. EXT. INT. INT. 1 1 2 2 3 3
OUT OUT
ZONE ZONE 2 2 FLASHER FLASHER
IN IN
7 8 9 10
6
SPEAKERS ( ( MINIMUM 6 OHMS SPEAKERS MINIMUM 6 OHMS ) )
ZONE 1 1 ZONE ZONE ZONE 2 2 ZONE ZONE 3 3
R R L L R R L L R R
m m Status output terminal (STATUS OUT)
These terminals are DC trigger output terminals to
determine whether power of a zone is on or off.
Connect these terminals to Keypads, etc.
• Rating of status output: 12V 100mA.
, , Flasher input terminal (FLASHER IN)
This terminal is to control the unit from each zone. Connect
the control signal from a Keypad, etc.
. . Remote control internal / external switch
(INT. / EXT.)
This switch is to select if the remote sensor on the front
panel work or not. If you use two or more ZS5300s in
cascade connection, set this switch at INT. for the ZS5300
that functions as the maser. Set the switch at EXT. for the
slave ZS5300s.
INT. : Enable the remote sensor.
EXT. : Disable the remote sensor.
⁄ ⁄ 0 0 ID select switch (ID SELECTOR)
When two or three ZS5300s are used, set independent ID
numbers for each. Up to 3 ZS5300s can be connected.
Different ID numbers must be set for each unit.
⁄ ⁄ 1 1 Voltage selector (VOLTAGE SELECTOR)
Select the power voltage of your location. You can select
115V or 230V.
• Be sure to disconnect the power cord when changing
this switch.
⁄ ⁄ 2 2 Power inlet (AC IN)
Plug the power cord into this socket.
CAUTION:
Be sure to use the power cord rating more than 2.5A, 250V
and 18AWG when operating 230V AC voltage.
L L
SERIAL NO. SERIAL NO.
MODEL NO. ZS5300
VOLTAGE SELECTOR VOLTAGE SELECTOR
115V 115V 230V 230V
AC IN AC IN
11 12
5