Eu Declaration Of Conformity - WEG W21 Manual De Instalación

EU DECLARATION OF CONFORMITY

Manufacturers:
WEG Equipamentos Elétricos S.A.
Av. Prefeito Waldemar Grubba, 3000
89256-900 - Jaraguá do Sul – SC – Brazil
www.weg.net
WEGeuro – Indústria Eléctrica S.A.
Headquarters:
Rua Eng. Frederico Ulrich,
Zona Industrial da Maia Sector V
4470-605 – Maia – Portugal
www.weg.net/pt
Contact person: Luís Filipe Oliveira Silva Castro Araújo
Authorised Representative in the European Union
(Single Contact Point)
Branch – Santo Tirso:
Rua António Joaquim Campos Monteiro, n° 510
Santa Cristina do Couto
4780-165 – Santo Tirso – Portugal
www.weg.net/pt
The manufacturer declares under sole responsibility that:
when installed, maintained and used in applications for which they were designed, and in compliance with the relevant installation standards and
manufacturer's instructions, comply with the provisions of the following relevant European Union harmonisation legislation, wherever applicable:
RoHS Directive 2011/65/EU** and its amendments (including Directive 2015/863/EU);
EMC Directive 2014/30/EU (electric motors are considered inherently benign in terms of electromagnetic compatibility)
The fulfilment of the safety objectives of the relevant European Union harmonisation legislation has been demonstrated by compliance with the following
standards, wherever applicable:
EN 60079-0:2018*/ EN 60079-1:2014*/ EN 60079-7:2015 + A1:2018*/ EN 60079 31:2014/
* A comparison of the current version of the EN 60079-0:2018, EN 60079-1:2014 and EN 60079-7:2015 + A1:2018 standards with the previous
versions used by some Baseefa, CESI, PTB and SIRA ATEX certificates shows that there are no changes in the "state of the art" applicable to the
product covered by this Declaration of Conformity. The manufacturer hereby declares that the ATEX Certificates issued by Baseefa, CESI, PTB and SIRA
meet the Essential Health and Safety Requirements of ATEX Directive 2014/34/EU.
** Electric motors with a voltage rating higher than 1000 V for alternate current and 1500 V for direct current are not under the scope.
*** Electric motors are considered partly completed machinery and are supplied with a " Declaration of Incorporation":
The products above cannot be put into service until the machinery into which they have been incorporated has been declared in conformity with the
Machinery Directive.
We undertake to transmit, in response to a reasoned request by the national authorities, relevant information on the partly completed machinery
identified above through WEG authorised representative established in the European Union. The method of transmission shall be electronic or physical
method and shall be without prejudice to the intellectual property rights of the manufacturer.
The Quality System for the certificates described above is approved by SGS Fimko Oy (NB0598) under the Quality Assurance Notification SGS ATEX
5886 (WEG Equipamentos Elétricos S.A. and WEG Linhares Equipamentos Elétricos S.A.) and SGS ATEX 3862 (WEGeuro – Indústria Eléctrica S.A.).
CE marking in: 1996
Jaraguá do Sul, May 28 , 2020
th
Signed for and on behalf of the manufacturer:
Alexandre Eiji Amano
Quality System & Certification Manager
2 | Electric motors for explosive atmospheres
WEG electric motors and components used for following motor lines:
W21, W22X..., W50X..., W60X..., HGF and EX61G
ATEX Directive 2014/34/EU;
Machinery Directive 2006/42/EC***;
EN 60204-1:2018 / EN 60204-11:2019 / EN 50581:2012 and IEC TS 60034-25:2014.
Declaration of Incorporation:
Brasil
WEG (Nantong) Electric Motor Manufacturing CO., LTD.
No. 128# - Xinkai South Road, Nantong
Economic & Technical Development
Zone, Nantong, Jiangsu Province – China
www.weg.net/cn
WEG (Jiangsu) Electric Equipment CO., LTD.
No. 15 Group, North City Street, Dengyuan Community
Rugao City, Jiangsu Province – China
www.weg.net/cn
WEG Linhares Equipamentos Elétricos S.A.
Rod. BR 101, Km 161,5, s/n
Distrito Industrial Rio Quartel
Bairro Rio Quartel de Baixo
29915-500 – Linhares – ES – Brazil
www.weg.net
...............
Edson José Koshinski
Engineering Director
China
Luis Filipe Araujo
Industrial Director
Portugal