User & Set-Up Instructions; General User Information; Control Set-Up Procedures; Start Operating Set-Up - Maytag MHN33PDCWW Instrucciones De Instalación

NOTE: After the washer has been installed and plugged in, the
display may show '0 MINUTES'. Once the washer has been plugged
in and the washer door opened and closed, the display will show the
price. In washers set for free cycles, the display will flash 'SELECT
CYCLE'.
1. PD Models: Insert coins until 'SELECT CYCLE' flashes
in display.
PR Models: A debit card is required rather than coins. In
Enhanced Debit mode, the card balance will also display when a
debit card is inserted into the reader.
2. Door must be closed before cycle selection is made,
3. Press fabric setting key pad for the wash cycle desired. After the
cycle is started, the time will display and count down.
4. If a cycle is interrupted by opening the door, 'RESELECT
CYCLE' will flash in the display. To restart the washer, close door,
and reselect desired cycle.

General User Information

SCROLLING 'OUT OF ORDER' SHOWING IN DISPLAY
This condition indicates the washer is inoperative.
'0 MINUTES' SHOWING IN DISPLAY
This indicates the cycle is complete and the washer cannot be
operated. Coins dropped or debit inputs during this condition will be
stored in escrow but cannot be used until normal operation is restored
by opening and closing the door. If a door switch fails, it must be
replaced before normal operation can be restored.
COLD START (Initial first use)
Washer is programmed at the factory as follows:
11-minute wash period
3 rinses (extra rinse not enabled)
$1.75 wash price (PD models)
$0 00 wash price (PR models)
WARM START (after power failure)
A few seconds after power is restored, if a cycle was in progress
at the time of the power failure, 'RESELECT CYCLE' will flash
in the display, indicating the need for a key press to restart the washer.
DOOR LOCK
Prior to beginning a cycle, there is a door lock routine of lock/unlock/
relock; then cycle begins. The door will remain locked until the end of a
cycle or approximately 2 minutes after a power interruption.
PRICING
After the door is opened following the completion of a cycle,
the display indicates the cycle price (unless set for free operation). As
coins are dropped or debit inputs arrive, the display will change to lead
the user through the initiation of a cycle.
FREE CYCLES
This is established by setting the cycle price to zero. When this
happens, 'SELECT CYCLE' will appear rather than a cycle price.
DEBIT CARD READY
This washer is debit card 'cable' ready. It will accept a variety of debit
card systems, but does NOT come with a debit card reader. Refer to
the debit card reader manufacturer for proper washer set-up. In models
converted to a Generation 1 debit card system, debit pulses represent
the equivalent of one coin (coin 1).
10
USER & SET-UP INSTRUCTIONS

Control Set-up Procedures

IMPORTANT: Read all instructions before operating.
PD Models: Insert access door key, turn, and lift to remove
access door.
PR Models: Once the debit card reader is installed (according
to the reader manufacturer's instructions), the set-up mode can
only be entered by inserting a set-up card (supplied by the reader
manufacturer) into the card slot. If a set-up card is not available,
diagnostic modes can be entered by removing connector AA1 on
the circuit board or by using the Service Access Code (see Service
Access Code section, page 14) for PR models set up as a PN.
The lower fabric setting key pads and the digital display are used to
set up the controls.
The display can contain four numbers and/or letters and a decimal
point. These are used to indicate the set-up codes and related code
values available for use in programming the washer.
HOW TO USE THE KEY PADS TO PROGRAM THE CONTROLS
1. POWERWASH – UPPER LEFT key pad is used to adjust
the values associated with set-up codes. Pressing the key
pad will increment the value. Rapid adjustment is possible
by holding the key pad down.
2. The TEMPERATURE – LOWER LEFT key pad is used to adjust
the values associated with set-up codes. Pressing the key
pad will decrement the value. Rapid adjustment is possible
by holding down the key pad.
3. The EXTRA RINSE – LOWER MIDDLE key pad will advance
through the set-up codes. Pressing the key pad will advance
to the next available set-up code. Holding the key pad down will
automatically advance through the set-up codes at a rate
of 1 per second.
4. The DELICATES – UPPER RIGHT key pad is used to select
or deselect options.

Start Operating Set-up

Before proceeding, it is worth noting that, despite all of the options
available, an owner can simply choose to uncrate a new commercial
washer, hook it up, plug it in, and have a washer that operates.
Washers are preset at the factory for an 11-minute wash period and
three rinses (no extra rinse).
SET-UP CODES
The EXTRA RINSE – LOWER MIDDLE key pad will advance
■
you from code to code.
The TEMPERATURE – LOWER LEFT and POWERWASH –
■
UPPER LEFT key pads will change the code value.
The DELICATES – UPPER RIGHT key pad will select or
■
deselect options.
FOR PR MODELS: The set-up codes are the same as for the "PD"
model except where noted.
The set-up code is indicated by the one or two left-hand characters.
The set-up code value is indicated by the two
or three right-hand characters.