Complete Installation; Electronic Controls Set-Up Instructions (Pd & Pr Models); General Information - Maytag MAT20PDFGW Instrucciones

COMPLETE INSTALLATION

WARNING
Electrical Shock Hazard
Electrically ground this appliance.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Check electrical requirements. Be sure that you have the
n
correct electrical supply and the recommended earthing
method.
Check that all parts are now installed. If there is an extra part,
n
go back through steps to see what was skipped.
Check that you have all of your tools.
n
Check that shipping materials were completely removed
n
from washer.
Dispose of/recycle all packaging materials.
n
Check that the water faucets are on.
n
Check for leaks around faucets and inlet hoses.
n
Remove film from console and any tape remaining on
n
washer.
Plug into an earthed outlet or connect power.
n
Check that circuit breaker is not tripped or fuse is not blown.
n
Start washer using the payment system (if available) to
n
check that the wash cycle completes without an error code
or water leak.
ELECTRONIC CONTROLS SET-UP
INSTRUCTIONS
Basic Operation of Commercial Washer
For additional information, see
n
www.maytagcommerciallaundry.com.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
14
(PD & PR MODELS)
IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished, but
failure may occur at a later date due to ESD stress.
Use an anti-static wrist strap. Connect wrist strap to green
n
ground connection point or unpainted metal in the washer.
Touch your finger repeatedly to a green earth connection
point or unpainted metal in the washer.
Before removing the part from its package, touch the
n
anti-static bag to a green earth connection point or
unpainted metal in the washer.
Avoid touching electronic parts or terminal contacts;
n
handle electronic control assembly by edges only.
When repackaging failed electronic control assembly in
n
anti-static bag, observe above instructions.

GENERAL INFORMATION

Blank Display
Check power to machine. Enter Service Mode and check for
Fault Code.
"0 Minutes" showing in display
This indicates the previous cycle is complete or a machine reset
was performed. Opening the lid will restore the display to the
Vend Price or Available state.
Factory Default Settings
Washer is programmed at the factory as follows:
POWERWASH = Hot Water Main Wash - Deep Rinse - Heavy
n
Soil Option Enabled- Extra Rinse Option Enabled - COIN
model pricing set to $2.50.
NORMAL = Warm Water Main Wash - Deep Rinse - No
n
Options Enabled - COIN model pricing set to $2.00.
DELICATES = Cold Water Main Wash - Deep Rinse - No
n
Options Enabled - COIN model pricing set to $1.75.
NORMAL ECO = Warm Water Main Wash - Progressive Spray
n
Rinse - No Options Enabled - COIN model pricing set to
$1.75.
Total calculated cycle price based on Base Cycle Cost +
n
Cost of Options Selected (Extra Rinse, Soil Level, and Water
Temperature). Default total cycle price dependent on Cycle
Settings selected. PowerWash cycle price will not reduce from
programmed settings (Base Cycle Price + Cost of Options
Selected per Cycle Settings) when end-user makes changes
to selected cycle options (in example changes hot water to
cold water). All other cycle prices are calculated based on
final cycle selections made by the end-user.
Warm Start (after power failure)
After a delay of up to 8 seconds, the washer is restored to
the portion of the cycle that existed at time of the power failure.
To continue the cycle, press START/PAUSE.
Free Cycles
This is established by setting the cycle price to zero. When this
happens, "SELECT CYCLE" will appear and cycle price will show
"0.00."
-OR-