General Recommendations; Description Of The Personnel; Technical Assistance; 3- Technical Description - TOPP C240 Instrucciones Para La Instalación Y El Empleo

IT 2
OWERVIEW
2.1

GENERAL RECOMMENDATIONS

Before installing and using the actuator the
installer and user must read and thoroughly
understand all parts of this manual.
This manual is an integral part of the actuator and must
&
be kept by the user, with all the enclosures, for future
reference.
This manual serves to furnish all the information
&
necessary so that, in addition to using the actuator
correctly, it can be managed in the most independent and
safest manner possible: TOPP srl is not liable for any
damages to persons, animals and property caused by
failure to comply with these instructions.
This manual was written by TOPP srl, which holds the
&
copyright. No part of it may be copied or published without
the manufacturer's written approval.
TOPP srl reserves the right to improve and amend the
&
manual and products described at any time and without
notice.
The information contained in this manual was written
&
and checked with the maximum care; however TOPP srl
has no liability for any errors due to omissions or errors in
printing or transmission.
To assure a correct performance of the system,
&
between the opening and closing command of the
actuators, it is required to leave the 2 poles control switch
in OFF position for at least 2 seconds.
In order for the automation unit to operate correctly, we
&
recommend carrying out periodical maintenance on it, as
indicated in par. 7.1 of this manual.
The warranty on the actuator will not be honored if
&
product is not installed and used according to the
instructions provided and the regulations shown in this
instruction manual and if it is used with non-genuine
parts, accessories, spare parts and/or control/feeding
units.
IT 3
TECHNICAL DESCRIPTION
3.1

RATING PLATE AND "EC" MARKING

The "CE" seal certifies conformity of the machine with the
essential health and safety requisites foreseen by the
European Product Directives.
It consists of an adhesive label in polyester, silkscreen
printed in black, with the following measurements: L= 60
mm - H= 24 mm, and it is applied to the outside of the
actuator. The following data are indicated legibly and
indelibly on the label :
the manufacturer's logo and address;
the type and model;
the voltage (V) and frequency (Hz) of the power supply;
C240
EN INSTALLATION AND USE INSTRUCTIONS
2.2

DESCRIPTION OF THE PERSONNEL

Specialized electrician
The expert must be able to install the actuator, start it
functioning with the power ON in the electrical cabinet
and shunt boxes. He is also qualified to perform any
electrical and mechanical repairs, adjustments and
maintenance.
Installation of the actuator must be made exclusively by
qualified technical personnel in possession of the
professional requisites foreseen by the legislation in
force in the country of installation.
The installation technician shall accept full responsibility
for any installation errors and for any failure to adhere to
the instructions provided in this manual. The installation
technician shall therefore be exclusively liable for any
damages caused to users and/or third parties that may
arise as a result of incorrect installation.
User
The user must be able to operate the actuator under
normal conditions, using the controls provided. The user
must also be able to operate the actuator during
maintenance and perform simple operations of routine
maintenance (cleaning), startup or resumption of use of
the actuator after a forced interruption.
The user must not perform operations restricted to
maintenance personnel or specialized experts. The
manufacturer is not liable for damages deriving from
failure to comply with this prohibition.
Use of the actuator must be assigned exclusively to users
who comply with the instructions in this manual and in the
manuals of the TOPP devices connected to it (e.g. power
unit).
2.3

TECHNICAL ASSISTANCE

Contact the installation technician or retailer for
assistance.
the intensity of the current absorbed (A);
electrical power absorbed P (W);
the thrust and traction force F (N);
the type of service S2 (min);
the speed of movement on empty (mm/s);
the degree of protection (IP);
the CE mark;
the "RAEE" Directive 2002/96 EC symbol;
the double insulation symbol (only model C240/230V);
the serial number.
15