Descargar Imprimir esta página

Fein Slugger JMU 137 QW Instrucciones De Uso página 4

Ocultar thumbs Ver también para Slugger JMU 137 QW:

Publicidad

Idiomas disponibles

Idiomas disponibles

OBJ_BUCH-0000000261-003.book Page 4 Thursday, April 27, 2017 7:47 AM
en
4
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotat-
ing part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose cloth-
ing or jewelery. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewelry or long hair can
be caught in moving parts.
g) If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of dust collec-
tion can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job bet-
ter and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the
switch is dangerous and must be
repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
Special safety instructions.
Wear protective equipment. Depending on the
application, wear face shield or safety gog-
gles. Wear hearing protection. The safety
glasses/goggles must be suitable to protect
against the particles emitted from different
operations. Continuous high exposure to
noise can lead to loss of hearing.
Do not touch the sharp edges of the core drill
bit. Danger of injury.
d) Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condi-
tion that may affect the power tool's
operation. If damaged, have the power
tool repaired before use. Many accidents
are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those
intended could result in a hazardous sit-
uation.
5) Service
a) Have your power tool serviced by a qual-
ified repair person using only identical
replacement parts. This will ensure that
the safety of the power tool is main-
tained.
Replace the protective cable bushing immedi-
ately when damaged. A defective protective
cable bushing can lead to overheating of the
machine and to an emergency stop.
Before putting into operation: Mount the chip
guard to the machine.
Always secure the power tool with with the
supplied clamping strap. In case of a power
failure or when the power plug is pulled, the
magnetic holding power is not maintained.
When carrying out such work, beware of fall-
ing objects, such as cores or chips.

Publicidad

loading

Este manual también es adecuado para:

Slugger jmu 137 mqwSlugger jmu 137-2 qwSlugger jmu 137 qw serieSlugger jmu 137 mqw serieSlugger jmu 137-2 qw serie