Alarm Title Setup - JVC TK-C676 Instrucciones

Setting Up the Camera Using an RM-P2580

ALARM TITLE Setup

Use the ALARM TITLE screen to set the alarm titles to be displayed when an alarm signal is transmitted.
Up to 10 alarm titles (ALARM TITLE 1 to 10) can be set and each title can be up to 12 characters in length.
MENU button
SET button
REMOTE CONTROL UNIT
CAMERA POSITION
SETUP
POWER
ALARM
MENU SET AUTO
KEY LOCK
LENS CAMERA/POSITION
1 2 3
CAMERA POSI-
SPEED
TION
IRIS 4 5 6 OPTION OPTION
CLOSE OPEN
1 2
FOCUS
7 8 9 AUTO AUTO
NEAR FAR
AF
PAN PATROL
0
WIDE ZOOM TELE CLEAR ENTER
/HOME
ENTER button
FAR button
WIDE button
NEAR button
– – – M E N U – – –
C A M . F U N C T I O N . .
C A M . T I T L E / A L A R M . .
C A M . V I D E O A D J U S T . .
C A M . A L C / E x D R . .
H O M E M O T I O N D E T E C T . .
A U T O P A N / P A T R O L / T R A C E . .
P O S I . F U N C T I O N S E T . .
F A C T O R Y S E T T I N G S . .
SETUP menu on camera
– – – C A M E R A T I T L E / A L A R M – – –
C A M . T I T L E E D I T . .
A R E A T I T L E O F F
A R E A T I T L E E D I T . .
A L M . T I T L E S I Z E D O U B L E
A L M . T I T L E C O L O U R W H I T E
A L A R M T I T L E E D I T . .
A L A R M I N P U T . .
A L A R M O U T P U T . .
TITLE/ALARM menu
Space Blinking Character area
– – – A L A R M T I T L E 1 – – –
0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K
L M N O P Q R S T U V W X Y Z
a b c d e f g
h i j k l m n o p q r s t u v w x y z . , '
– : / Ä Ö Ü Â Ê Î Ô Û Ç Ñ ä ë ï ö ü â ê î ô
û á é í ó ú à è ì ò ù ç ñ ß ¡ ¿
←W I D E T E L E →
→
T I T L E N O . S E L E C T F O C U S
Blinking
ALARM TITLE screen
RM-P2580 units need to be configured to display Alarm Titles. Use the RM-P2580 menu settings
to do this:
1. Press and hold the MENU button for 3 seconds to display the SETUP screen on the remote control unit.
2. First select the CONTROL UNIT screen, then the DATA I/O screen and finally the INPUT ASSIGNMENT screen.
3. Select "ALARM TEXT" then "EDIT 1", the alarm title set as ALARM TITLE 1 is displayed on the monitor.
* The alarm signals are input into the DATA I/O terminals on the rear panel of the RM-P2580.
E-32
RM-P2580
F-1 F-2 F-3
CAMERA
PAN/TILT
buttons
PAN/TILT
lever
TELE button
Title input
field
1.
Select the camera. (
CAMERA button → Numeric key (camera number) → ENTER but-
ton.
The picture of the selected camera is output.
2.
Display the SETUP menu on the camera.
1
( P. 18, steps to
MENU button (3 sec.) → Select "CAMERA" with the PAN/TILT lever
→ SET button.
The camera moves to the home position.
3.
Tilt the PAN/TILT lever up or down to move the cur-
sor (>) to "CAMERA TITLE/ALARM" and press the
SET button.
The TITLE/ALARM screen is displayed.
4.
Move the cursor (>) onto the item "ALARM TITLE
EDIT" and press the SET button.
• The ALARM TITLE 1 menu is displayed.
• The first few characters in the character area and title input field
blink to indicate that the system is ready for a title input.
5.
Tilt the PAN/TILT lever to select the first character
of the title from the character area.
• The character being selected blinks.
• The selected character is displayed in the title input field.
6.
Press the TELE button.
• The first character of the title is input, and the system gets ready
for the input of the second character.
• If the WIDE button is pressed, the blinking position in the title in-
put field moves to the left. Use this facility to correct previously
input characters.
7.
Press the FAR button.
• The next ALARM TITLE screen is displayed.
• If the NEAR button is pressed, the previous ALARM TITLE screen
is displayed.
8.
5
Repeat steps to
Complete the input of all the alarm titles (ALARM TITLE 1 to 10) in
this way.
9.
Press the MENU button.
• The screen returns to the previous menu.
RM-P2580 Instruction manual)
4
)
7
for each alarm title.