Yamaha MOTIF-RACK ES Manual De Uso página 98

Formato de datos MIDI
(3-2-3) ALL NOTE OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0)
All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain or
Sostenuto is on, notes will continue sounding until these are turned off.
(3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF.
Sets VOICE RECEIVE CHANNEL to "OMNI OFF," channel 1.
(3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF.
Sets VOICE RECEIVE CHANNEL to "OMNI ON."
(3-2-6) MONO (CONTROL NUMBER = 7EH, DATA VALUE = 0..16)
Performs the same function as when receiving ALL SOUNDS OFF. If the 3rd byte (mono) is within 0 through 16, the
channel will be Mode 4 (m = 1).
In the Voice mode, the mode can be Mode 2 (m = 1) according to VOICE RECEIVE CHANNEL.
(3-2-7) POLY (CONTROL NUMBER = 7FH, DATA VALUE = 0)
Performs the same function as when receiving ALL SOUNDS OFF. The channel will be Mode3.
In the Voice mode, the mode can be Mode 1 according to VOICE RECEIVE CHANNEL.
(3-3) REGISTERED PARAMETER NUMBER
STATUS 1011nnnn(BnH) n = 0 - 15 CHANNEL NUMBER
LSB 01100100(64H)
RPN LSB 0ppppppp
MSB 01100101(65H)
RPN MSB 0qqqqqqq
DATA ENTRY MSB 00000110(06H)
DATA VALUE 0mmmmmmm
DATA ENTRY LSB 00100110(26H)
DATA VALUE 0lllllll
First, designate the parameter using RPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB.
RPN D.ENTRY
LSB MSB MSB LSB PARAMETER NAME
00H 00H mmH --- PITCH BEND SENSITIVITY
01H 00H mmH llH MASTER FINE TUNE
{mmH,llH}={00H,00H}-{40H,00H}-{7FH,7FH}
(-8192*100/8192) - 0 - (+8192*100/8192)
02H 00H mmH --- MASTER COARSE TUNE
28H - 40H - 58H (-24 - 0 - +24 semitones)
7FH 7FH --- --- RPN RESET
RPN numbers will be left not designated.
The internal values are not affected.
(3-4) NON-REGISTERED PARAMETER NUMBER
There are no applicable parameters.
These are transmitted to the Plug-in Board.
(3-5) SYSTEM REAL TIME MESSAGES
(3-5-1) ACTIVE SENSING
STATUS 11111110(FEH)
Once this code is received, the instrument starts sensing. When neither status nor data is received for over
approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the sustain switch
are forcibly turned off. In this case, each control data will be reset to a certain value.
(3-6) SYSTEM EXCLUSIVE MESSAGE
(3-6-1) UNIVERSAL NON REALTIME MESSAGE
(3-6-1-1) GENERAL MIDI MODE ON
F0H 7EH 7FH 09H 01H F7H
The PLG100-XG Plug-in Board installed to the instrument will receive this message when the instrument
is in the Multi mode and SYSTEM Receive GM/XG is set to on.
The internal Part values will be reset according to the SYSTEM when the Port is set to 1.
(3-6-1-2) IDENTITY REQUEST (Receive only)
F0H 7EH 0nH 06H 01H F7H
("n" = Device No. However, this instrument receives under "omni.")
(3-6-1-3) IDENTITY REPLY (Transmit only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 7FH F7H
dd; Device Number Code
MOTIF-RACK ES: 19 06
(3-6-2) UNIVERSAL REALTIME MESSAGE
(3-6-2-1) MIDI MASTER VOLUME
F0H 7FH 7FH 04H 01H llH mmH F7H
Sets the MASTER VOLUME value.
The value "mm" is used to set the master volume (the value "ll" should be ignored).
(3-6-3) PARAMETER CHANGE
(3-6-3-1) XG SYSTEM ON
11110000 F0
01000011 43
0001nnnn 1n
01001100 4C
0aaaaaaa 0
0aaaaaaa 0
0aaaaaaa 7E
0 0
11110111 F7
In MULTI MODE, received only when the PLG100-XG is installed and SYSTEM Receive GM/XG on is set
to on.
Be aware that executing this message takes about 170 ms and that, therefore, a certain interval before
executing the following message is needed.
98
Manual de uso
p = RPN LSB (Refer to the table as shown below.)
q = RPN MSB (Refer to the table as shown below.)
m = Data Value
l = Data Value
Exclusive Status
YAMAHA ID
Device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
(3-6-3-2) NATIVE PARAMETER CHANGE, MODE CHANGE
11110000 F0
01000011 43
0001nnnn 1n
01111111 7F
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0ddddddd ddddddd
| |
11110111 F7
For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.
For Address, see the MIDI Data Table in the separate Data List.
(3-6-4) BULK DUMP
11110000 F0
01000011 43
0000nnnn 0n
01111111 7F
00000000 00
0bbbbbbb bbbbbbb
0bbbbbbb bbbbbbb
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0 0
| |
0ccccccc ccccccc
11110111 F7
For Address and Byte Count, see the MIDI Data Table in the separate Data List.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address, Data
and Check sum itself are added.
(3-6-5) DUMP REQUEST
11110000 F0
01000011 43
0010nnnn 2n
01111111 7F
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
For Address and Byte Count, see the MIDI Data Table in the separate Data List.
(3-6-6) PARAMETER REQUEST
11110000 F0
01000011 43
0011nnnn 3n
01111111 7F
00000000 00
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
For Address, see the MIDI Data Table in the separate Data List.
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
Byte Count
Byte Count
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
Address High
Address Mid
Address Low
End of Exclusive
Exclusive Status
YAMAHA ID
Device Number
Model ID
Model ID
Address High
Address Mid
Address Low
End of Exclusive