Environmental Protection - Worx WG730E Manual Original

during operation will reduce the cutting area.
The table below gives the relationship between cutting
conditions and cutting area.
Cutting Height
Cutting 3 cm to 7 cm
TIPS:
1) It is recommended to mow your lawn more frequently,
walk at normal pace, and not to start/stop the mower
too often during operation.
2) For best performance, please ensure use two fully
charged battery packs at the same time and always cut
off 1/3 or less of the grass height.
3) Walk slowly when cutting long grass, so as to have more
effective cutting and properly discharge the clippings.
4) Avoid cutting wet grass, otherwise it will stick to the
underside of the deck and the clippings cannot be
collected or discharged properly.
5) A higher cutting height shall be applied to new or thick
grass and it will extend the battery duration.
MAINTENANCE
WARNING: Stop the mower, remove the safety
key and battery before removing the grass
collection bag.
NOTE: To ensure long and reliable service, perform the fol-
lowing maintenance procedures regularly. Check for obvious
16
defects such as a loose, dislodged or a damaged blade, loose
fittings, and worn or damaged components. Check that
the covers and guards are all undamaged and are correctly
attached to mower. Carry out any necessary maintenance or
repairs before operating mower. If the mower should happen
to fail despite regular maintenance, please call our customer
helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A
DULL BLADE DOES NOT CUT GRASS CLEANLY OR MULCH
PROPERLY.
WEAR PROPER EYE PROTECTION WHILE REMOVING, SHARP-
ENING, AND INSTALLING BLADE. ENSURE THAT SAFETY KEY
AND BATTERIES ARE REMOVED.
Sharpening the blade twice during a mowing season is
usually sufficient under normal circumstances. Sand causes
the blade to dull quickly. If your lawn has sandy soil, more
frequent sharpening may be required.
REPLACE BENT OR DAMAGED BLADE IMMEDIATELY.
WHEN SHARPENING THE BLADE
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade to keep it
balanced, removing equal amounts of material from both
ends.
NOTE:
1. Be sure the mower is turned off . Remove the key and
batteries.
2. Place the mower in stand up storage mode.
Cordless Lawn Mower
TO SHARPEN BLADE IN A VISE (SEE Fig. L)
1. Be sure the bail handle is released, the blade has
Cutting Area
(maximum) 2. Remove blade from mower. See instructions for remov-
200m *
2 3. Secure blade L-1 in a vise L-2.
4. Wear safety glasses and be careful not to cut yourself.
5. Carefully file the cutting edges of the blade with a fine
6. Check balance of blade. See instructions for blade
7. Replace blade on mower and tighten securely. Refer to
BLADE BALANCING (See Fig. M)
Check balance of blade by placing center hole in blade M-1
over a screwdriver shank M-2, clamped horizontally in a vise
M-3. If either end of the blade rotates downward, file that
end. Blade is properly balanced when neither end drops.
BLADE MAINTENANCE (See Fig. N1, N2)
Replace yourMower Blade after 50 hours mowing or 2 years,
which ever is the sooner-regardless of condition.
Follow these procedures to remove and replace the Blade.
You will need garden gloves (not provided) and a spanner
wrench (not provided) to remove the Blade. Make sure safety
key and batteries are not installed. Wedge a block of wood
between the blade and the mower deck to prevent the blade
from turning and unscrew the Blade Bolt counter-clockwise
using a spanner wrench, and then remove the Blade.
To re-assemble, position the Blade with the cutting edges
towards the ground. Then securely tighten the Blade Bolt.
STORAGE (See Fig. K1, K2)
Stop the mower, and always remove the Safety Key and bat-
teries. Clean the exterior of the machine thoroughly using a
soft brush and cloth. Do not use water, solvents or polishes.
Remove all grass and debris, especially from the ventilation
slots.
Turn the machine on its side and clean the blade area. If
grass cuttings are compacted in the blade area, remove with
a wooden or plastic implement.
Store the machine in a dry place. Do not place other objects
on top of the machine.
To aid storage, Press and hold Quick-release button, and fold
the Handle bar.
ENVIRONMENTAL
PROTECTION
recycling advice.
stopped and the safety key and battery removed before
removing the blade.
ing and attaching blade.
tooth file L-3 or sharpening stone.
balancing.
instructions below.
Waste electrical products must not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authorities or retailer for
EN