Rear Panel - JVC BD-X201MS Manual De Instrucciones

Ocultar thumbs Ver también para BD-X201MS:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 250

Rear Panel

f
e
1VIDEO LINE IN terminal (BNC)
This terminal allows composite video signals to be input to
the DVD recorder.
In order to select these signals for input, set INPUT
SELECT from the INPUT SELECT MENU screen to LINE.
• SETUP from the SYSTEM MENU (1/2) screen should be
set in accordance with whether or not this input signal is
a setup signal. (NTSC only)
2VIDEO Y/C IN terminal (4-pin)
This terminal allows YC separate video signals to be input
to the DVD recorder.
In order to select these signals for input, set INPUT
SELECT from the INPUT SELECT MENU screen to Y/C.
• SETUP from the SYSTEM MENU (1/2) screen should be
set in accordance with whether or not this input signal is
a setup signal. (NTSC only)
• This terminal's specification (i.e., S1 or S2) can be
selected using Y/C TERMINAL MODE from the SYS-
TEM MENU (2/2) screen.
3VIDEO LINE OUT terminal (BNC)
This terminal is used to connect the DVD recorder to a
monitor.
• When the DVD recorder is in Stop or Recording mode,
the video input signal is output on the E-E screen as a
composite video signal.
• If the REC button is pressed and held for at least 2 sec-
onds while the DVD recorder is stopped, the input signal
will be subjected to MPEG encode/decode processing
and output via the VIDEO LINE OUT terminal. This will
continue for as long as the REC button is held, and it
allows the DVD recording quality to be confirmed.
• Playback from the DVD is output as a composite signal
when in Playback mode.
• The Setup Menu, title menu, chapter menus, and other
setting and control screens are displayed on the monitor
connected to this terminal.
• Status and alarm information is also displayed on-
screen. (The DISPLAY MENU screen can be used to
indicate which items are to be displayed.)
All manuals and user guides at all-guides.com
2
1
3 45
d
c
b
Component Names & Functions
6
7
a
0
9
4VIDEO Y/C OUT terminal (4-pin)
For output of YC separate video signals.
• Information that is the same as that of the VIDEO LINE
OUT terminal is being output.
• This terminal's specification (i.e., S1 or S2) can be
selected using Y/C TERMINAL MODE from the SYS-
TEM MENU (2/2) screen.
5AUDIO INPUT LEVEL switch
This switch is used to set the standard level for audio input.
+4 dB : The standard level is set to +4 dB.
–8 dB : The standard level is set to –8 dB.
6AUDIO IN terminals (RCA × 2)
These terminals allow analog audio signals to be input to
the DVD recorder.
• In order to select these signals for input, set INPUT
SELECT from the INPUT SELECT MENU screen to
LINE or Y/C.
7AUDIO OUT terminals (RCA × 2)
These terminals allow analog audio signals to be output
from the DVD recorder.
• When the DVD recorder is in Stop or Recording mode,
the audio input signals (i.e., E-E signals) are output via
these terminals.
• Audio from the DVD is output when in Playback mode.
8RS-232C REMOTE terminal (D-sub 9-pin female)
Operation of this unit can be controlled externally by con-
necting to an RS-232C control device.
9USB terminals (× 2)
For connecting to a USB-supported keyboard.
The input of text in setting screens is carried out using a
keyboard.
• It is not be possible to operate devices other than a key-
board by connecting them to the USB terminal.
• Set KEYBOARD STYLE from the SYSTEM MENU (1/2)
screen in accordance with the keyboard's input lan-
guage.
Recommended manufacturers: Logitech
8
E-13

Publicidad

Tabla de contenido
loading

Tabla de contenido