optrel SWISS AIR Manual De Usuario página 13

Weight 1200 g / 42.33 oz (including filter, belt and battery)
Dimensions L x W x H: 250 x 170 x 50 mm
Operating and
-5 ° C to + 55 ° C
storage temperature
Norms EN 12941, EAC TP TC 019/2011, AS / NZS 1716
Notified body CE 1024
Temperature
and altitude Yes, if the control panel is connected
compensation
Scope of delivery / spare parts
See page V�
control panel (optional accessory)
If you use the optional control panel, please note the additional information in
these instructions�
swiss air carrying unit - explanation on page I.
a1 Measure your circumference to set the correct size (step a2)
a2 Set XS-M or M-XL to match your size
a3 Put the Carrying unit on as shown in the picture
a4 Close the belt hook as shown
a6 Adjust the size of the carrying unit in the shoulder area
a7 Adjust the width of the carrying unit to your body
a8 You can carry the device on your back at two heights; for adjustment, see
steps a9 - a10
a9 Loosen the Velcro fasteners and adjust to the desired height
a10 Fasten the Velcro straps again with light pressure
a11 Check that the carrying unit is sitting correctly and comfortably
swiss air mask - explanation on page II
b1 Make sure that the air hose connector is pointing downwards
b2 Loosen the neck strap with the side tabs
b3 Mount the mask on one side with the Y-tube
b4 Put on the mask with one side mounted
b5 Tighten the neck strap until it rests against your neck
b6 Click in the second side of the mask
b7 Pull the tabs on the headgear until the headgear is comfortable and secure
b8 Tighten the mask gasket as shown so that the mask seals properly
b9 Be careful not to pinch the nasal pillow, if it does, go to step b10
b10 If it is too tight you can remove the perforated part of the cushion
b11 final exam:
b11.1 Switch on the fresh air system at level 1
b11.2 Take a quick breath
b11.3 The mask should pull against your face as you inhale
b11.4 If this is not the case, the sealing of the mask is not correct
b11.5 If the test was successful you can start your work
swiss air device - explanation on page III
c1 Switch the device on using the on / off switch. Press twice if the device has not
been used for more than 3 hours
c2 Select the air flow by briefly pressing the on / off switch, you will receive an
acoustic signal (level 1 = 1 beep, level 2 = 2 beeps etc.)
c3 Switch off the device by pressing the on / off switch for 2s
c4 Carefully pull the catch from the filter cover to loosen it
c5 Remove the filter cover
c6 Change the pre-filter and the particle filter
c7 Push the filter cover back in
c8 Until you hear a click
c9 Carefully pull on the latch of the battery to release it
Pull the battery completely out of the housing
c10 Charge the battery with the supplied charger
c11 Close the filter cover again.
c12 If a hose change is necessary, pull the clip out of the housing, replace the
hose and reinsert the clip�
swiss air control panel - Explanation on page IV
d1� swiss air control panel
• Make sure that the plug is completely inserted into the socket. When the control
unit is plugged in again, first switch it off at the control panel and then set the
desired air flow.
• Always use the control panel to switch on and off (if connected). If you press the
On button on the device while the control panel is connected, an alarm will sound.
• If the control panel is unplugged during operation, the device automatically
switches to level III.
• If the particle filter is clogged or no particle filter is inserted, the control panel
displays an error and an acoustic signal sounds�
Battery indicator
d2. 100% - 75% - All four display LEDs light up green
d3. 75% - 50% - Three display LEDs light up green
d4. 50% - 25% - Two display LEDs light up green
d5. 25% - 10% - A display LED lights up yellow
d6. 10% - 0% - A display LED flashes red
Filter status
d7. New / unused particle filter - An indicator LED lights up green
d8. Little-used particle filter (6) - Three indicator LEDs light up green
d9. Heavily used particle filter (6) - Five indicator LEDs light up green
d10. Particle filter clogged / not inserted correctly / not inserted - five LEDs flash
green, four LEDs flash red
Explanation of symbols on page VI
e1 Read and understand the operating instructions
e2 Do not use sharp objects to open
e3 Fragile content
e4 Lay with this side up
e5 Protect from moisture
e6 certification body
e7 contains lithium ions
e8 reusable material
e9 Recommended storage: -5 C ° to +55 C °
e10 Do not dispose of as domestic waste, but in accordance with the national
regulations for hazardous waste.
Declaration of conformity
See the Internet address on the last page of this manual.
Legal Information
This document complies with the requirements of EU Regulation 2016/425 point
1.4 of Annex II.
Notified body
See the last page of this manual for detailed information.
13