Technical Specifications - Rupes LHR21III Instrucciones De Uso Y Anutencion

PICTOGRAPH

TECHNICAL SPECIFICATIONS

TYPE
Ø POLISHING FOAM mm
Ø BACKING PAD mm
Ø ORBIT mm
POWER W
R.P .M. /min.
WEIGHT according to EPTA-Procedure 01/2003 Kg
ELECTRONIC SPEED CONTROL
INSULATION CLASS
The values shown are based on a nominal voltage of 230V/50Hz. In the case of voltages and frequencies of different power values may vary. Refer to the label technical
specifi cations to the nominal values of the tool.
WARNINGS
The safety and accident prevention instructions are reported
in the "SAFETY INSTRUCTION" booklet which is an integral
part of these documents. This operating instructions manual
indicates the additional information required for the specifi c
use of the tool.
CORRECT USAGE
This tool is designed to be used as a polisher. Read all the
warnings, instructions, indications provided on drawings
and specifi cations supplied with this tool. Failure to comply
with all the instructions provided below may cause electrical
shocks, fi re and/or serious injuries.
This tool is not intended to be used for smoothing, metal
brushing and cutting operations. The use of this tool for
unintended applications may cause hazards and injuries to
people.
The tool must be used with accessories that have been
specifi cally designed or recommended by the manufacturer.
The fi xing of the accessory to the tool does not guarantee a
safe operation.
The rated speed of the accessories must be at least
equivalent to the maximum speed specifi ed on the tool.
Using the accessories at speeds above the rated one, may
cause them to break or be projected into the air.
The external diameter and thickness of the accessories
must match the specifi cations of the tool. Accessories
with incorrect dimensions cannot be adequately protected or
controlled.
The confi guration of accessories must match the tool.
The use of accessories that cannot be perfectly fi tted on the
Warning symbol/ Warning message
Read instruction manual
Wear eye protection
Wear ear protection
Wear a mask
Wear a gloves
CE compliant
EurAsian Mark
Italian Quality Mark
C-Tick Mark
Disposal of decommissioned
Arrow Act in the direction indicated by the arrow direction
III
LHR 21
180
150
21
500
3000 ÷ 4500
2,70
•
/ II
tool may result in imbalance, excessive vibrations and in the
impossibility of controlling the tool.
Do not use damaged accessories. Before use, inspect all
the accessories. Inspect the supporting pads and verify
there are no cracks, tears or excessive wear. If the tool or
accessory has fallen, verify that it is not damaged or install
a new accessory. After inspecting or installing an accessory,
test the operation of the tool at maximum speed and without
load for one minute, keeping at a safety distance. If the
accessories are damaged, they will break during this test.
STARTING UP
Voltage and power frequency must match the data
displayed on the identifi cation plate (1). Make sure that
tool is switched off before plug is connected.
TOOL ASSEMBLY
Position the cap (7) on the gearbox such that the holes for
mounting the screws (5) are aligned with those on the gearbox.
ACCESSORIES ASSEMBLY
BACKING PAD (Pic 1 to Pic 4)
- Place the disc pad (9) in the centre (4);
- slightly turn the disc pad (9) until it is fi xed to the screw;
- tighten the disc pad fi xing screw using the supplied disc pad
Allen wrench (10). Do not tighten the disc pad if it is in the
wrong position.
POLISHING FOAM
Apply pressure on polishing pad to join pad to plate (9).
START AND STOPPING
- Starting: push the lever of the switch (2) towards the body
ENGLISH
ISO7010 - W001
ISO7010 - M002
ISO7010 - M004
ISO7010 - M003
ISO7010 - M016
ISO7010 - M009
III
LHR 15
150
125
15
500
3000 ÷ 5200
2,60
•
/ II
6