Technical Specifications - Rupes ER303TE Traducción Del Manual De Instrucciones Original

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
PICTOGRAPH

TECHNICAL SPECIFICATIONS

TYPE
Ø ORBIT
Ø BACKING PAD
HOLES BACKING PAD
POWER
R.P .M.
WEIGHT
ELECTRONIC SPEED CONTROL
FITTING
VACUUM SYSTEM
PAD TYPE
INSULATION CLASS
The values shown are based on a nominal voltage of 230V/50Hz. In the case of voltages and frequencies of different power values may vary. Refer to the label technical
specifications to the nominal values of the tool.
WARNINGS
The safety and accident prevention instructions are reported
in the "SAFETY INSTRUCTION" booklet which is an integral
part of these documents. This operating instructions manual
indicates the additional information required for the specific
use of the tool.
CORRECT USAGE
This tool is designed to be used as a sander. Read all the
warnings, instructions, indications provided on drawings
and specifications supplied with this tool. Failure to comply
with all the instructions provided below may cause electrical
shocks, fires and/or serious injuries.
This tool is not intended to be used for metal brushing,
polishing and cutting operations. The use of this tool for
unintended applications may cause hazards and injuries to
people.
The tool must be used with accessories that have been
specifically designed or recommended by the manufacturer.
The fixing of the accessory to the tool does not guarantee a
safe operation.
The rated speed of the accessories must be at least
equivalent to the maximum speed specified on the tool.
Using the accessories at speeds above the rated one, may
cause them to break or be projected into the air.
The external diameter and thickness of the accessories
must match the specifications of the tool. Accessories
with incorrect dimensions cannot be adequately protected or
controlled.
The configuration of accessories must match the tool.
The use of accessories that cannot be perfectly fitted on the
Warning symbol/ Warning message
Read instruction manual
Wear eye protection
Wear ear protection
Wear a mask
Wear a gloves
CE compliant
EurAsian Mark
C-Tick Mark
Disposal of decommissioned
Insulation class II
Arrow
Act in the direction indicated by the arrow direction
ER303TE
mm
3
mm
[W]
[/min]
[kg]
tool may result in imbalance, excessive vibrations and in the
impossibility of controlling the tool.
Do not use damaged accessories. Before use, inspect all
the accessories. Inspect the supporting pads and verify
there are no cracks, tears or excessive wear. If the tool
or accessory has fallen, verify that it is not damaged or
install a new accessory. After inspecting or installing
an accessory, test the operation of the tool at maximum
speed and without load for one minute, keeping at a safety
distance. If the accessories are damaged, they will break
during this test.
SPECIFIC SAFETY WARNINGS
Do not use sandpaper any larger in size than the sanding
discs. Follow the manufacturers' instructions when choosing
the sandpaper.
The use of a larger sheet of sandpaper extending beyond the
sanding disc can cause tearing and tangling, leading to jerking
movements.
STARTING UP
Voltage and power frequency must match the data
displayed on the identification plate (1). Make sure that
tool is switched off before plug is connected.
ACCESSORIES ASSEMBLY
BACKING PAD
1. Place the backing pad (6) with the screw in the centre (fig.1);
2. slightly turn the backing pad until it is in right position (fig.2);
3. tighten the backing pad fixing screw using the supplied Allen
ENGLISH
ISO7010 - W001
ISO7010 - M002
ISO7010 - M004
ISO7010 - M003
ISO7010 - M016
ISO7010 - M009
ER305TE
5
150
MULTIHOLE
350
5800-10000
1.87
M8
VELCRO
II/
7
7

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Er305te

Tabla de contenido