Sauder 419956 Manual De Instrucciones
  1. Manuales
  2. Marcas
  3. Sauder Manuales
  4. Muebles de Interior
  5. 419956
  6. Manual de instrucciones

Sauder 419956 Manual De Instrucciones

Ocultar thumbs

Publicidad

Tabla de contenido

sauder.com
L-Desk
Costa Collection | Model 419956
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
For all your
newfangled gadgetry.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-44
Français pg 45-50
Español pg 51-56
Lot # 394629
09/27/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicidad

Tabla de contenido
loading

Manuales relacionados para Sauder 419956

Resumen de contenidos para Sauder 419956

  • Página 1 Costa Collection | Model 419956 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
  • Página 2 RETURN TOP (1) D109 DRAWER BACK (2) RIGHT KEYBOARD UPRIGHT (1) RIGHT PANEL (1) D707 LARGE DRAWER BOTTOM (1) RIGHT MODESTY PANEL (1) LEFT PANEL (1) D716 DRAWER BOTTOM (2) LEFT FRONT LEG (2) DOOR (1) Page 2 419956 www.sauder.com/services...

  • Página 3: Part Identifi Cation

    While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. D109 D716 D109 D716 D707 www.sauder.com/services 419956 Page 3...
  • Página 4 HIDDEN CAM - 37 12F TWIST-LOCK ® CAM SCREW - 37 FASTENER - 24 WOOD DOWEL - 16 CONNECTOR PLATE - 2 14H HINGE - 2 KNOB SET - 4 136K DOOR STOP - 1 GLUE - 1 Page 4 419956 www.sauder.com/services...
  • Página 5 18S BROWN 1" FLAT HEAD SCREW - 4 BLACK 1-1/8" MACHINE SCREW - 4 30S BLACK 1-9/16" FLAT HEAD SCREW - 12 BLACK 9/16" FLAT HEAD SCREW - 26 113S BLACK 1-15/16" FLAT HEAD SCREW - 9 www.sauder.com/services 419956 Page 5...
  • Página 6 Assemble your unit on a carpeted fl oor or on the empty carton to å avoid scratching your unit or the fl oor. STOP To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (12F) å into the large holes in the ENDS (A and B). If you purchased...
  • Página 7 ENDS (A and B), UPRIGHTS (D and E), BACKS (F), LEFT MODESTY PANEL (G), and RIGHT PANEL (Z). Arrow Arrow (37 used) Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. www.sauder.com/services 419956 Page 7...
  • Página 8 Step 3 Turn thirty-seven CAM SCREWS (8F) into the LEGS (H, P, Q å and R) and PANELS (Z and AA). (37 used) Page 8 419956 www.sauder.com/services...
  • Página 9 The MOLDINGS should be centered over the ENDS, UPRIGHTS, and BACKS. BLACK 9/16" FLAT HEAD SCREW (12 used in this step) Shoulder Shoulder Apply pressure with your hands as you guide the MOLDINGS over the SCREWS and onto the ENDS, UPRIGHTS, and BACKS. www.sauder.com/services 419956 Page 9...
  • Página 10 ENDS, UPRIGHTS, and BACKS. Be sure these edges are even after the MOLDING is slid on. Shoulder Apply pressure with your hands as you guide the MOLDINGS over the SCREWS and onto the ENDS, UPRIGHTS, and BACKS. Page 10 419956 www.sauder.com/services...
  • Página 11 ENDS, UPRIGHTS, and BACKS. Be sure these edges are even after the Angled edge MOLDING is slid on. Shoulder Apply pressure with your hands as you guide the MOLDINGS over the SCREWS and onto the ENDS, UPRIGHTS, and BACKS. www.sauder.com/services 419956 Page 11...
  • Página 12 S u r f a c Edge with i t h TWIST-LOCK® I S T - L O F A S FASTENERS T E N ® E R S These surfaces should be even. End without hole Page 12 419956 www.sauder.com/services...
  • Página 13 S u r f a c i t h I S T - L O F A S T E N ® E R S Edge with TWIST-LOCK® FASTENERS These surfaces should be even. Edge with hole www.sauder.com/services 419956 Page 13...
  • Página 14 Fill the holes 1/4 to 1/2 full with GLUE. Caution Inspect the parts thoroughly before assembling. Disassembly of glued parts is extremely diffi cult. These surfaces should be even. End without hole Edge with TWIST-LOCK® FASTENERS These surfaces should be even. End without hole Page 14 419956 www.sauder.com/services...
  • Página 15 S u r f a c i t h I S T - L O F A S T E N ® E R S Edge with TWIST-LOCK® FASTENERS These surfaces should be even. Edge with hole www.sauder.com/services 419956 Page 15...
  • Página 16 NOTE: The WIDE EXTENSION SLIDES will be used later for the LARGE DRAWERS. å Push the black lever in and pull the SLIDE from the RAIL. Open end Edge with TWIST-LOCK® FASTENERS Open end GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 16 419956 www.sauder.com/services...
  • Página 17 NOTE: The NARROW EXTENSION SLIDES will be used later for the SMALL DRAWERS. å Push the black lever in and pull the SLIDE from the RAIL. Open end GOLD 5/16" FLAT HEAD SCREW (8 used in this step) Open end www.sauder.com/services 419956 Page 17...
  • Página 18 The BACK MOLDINGS (K) S u r should be here. f a c i t h D E N H I D H I D D E N i t h f a c S u r Page 18 419956 www.sauder.com/services...
  • Página 19 T E N T E N ® E R S F A S How to use the SAUDER TWIST-LOCK ® FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
  • Página 20 Step 15 Fasten the UPRIGHTS (D and E) to the BACKS (F) and å BOTTOMS (C). Tighten four TWIST-LOCK® FASTENERS Don't worry. It isn't and four HIDDEN CAMS. Rome. This can be built in a day. Page 20 419956 www.sauder.com/services...
  • Página 21 Skip this step and the next step if you did not purchase å the 419958 Hutch. The 419956 L-Desk was made to hold the 419958 Hutch å There are two options for fastening the Hutch to the L-Desk as shown.
  • Página 22 Diagram 2 confi guration. have been engineered to be lighter, stronger, faster… well ok. Not technically faster. But defi nitely makes for a sturdier L Desk that’ s easier to assemble and friendlier to the environment. Page 22 419956 www.sauder.com/services...
  • Página 23 Fill the holes 1/4 to 1/2 full with GLUE. Caution STOP Inspect the parts thoroughly before assembling. Disassembly of glued parts is extremely diffi cult. If you purchased the 419958 Hutch, assemble that unit fi rst. This large hole must be here. www.sauder.com/services 419956 Page 23...
  • Página 24 å Tighten two TWIST-LOCK® FASTENERS. Fasten the LEFT MODESTY PANEL (G) to the LEFT å UPRIGHT (E). Use three BLACK 1-15/16" FLAT HEAD SCREWS (113S). 113S BLACK 1-15/16" FLAT HEAD SCREW (3 used in this step) Page 24 419956 www.sauder.com/services...
  • Página 25 Tighten one TWIST-LOCK® FASTENER. Fasten the RIGHT MODESTY PANEL (O) to the LEFT å MODESTY PANEL (G). Use three BLACK 1-15/16" FLAT HEAD SCREWS (113S). 113S BLACK 1-15/16" FLAT HEAD SCREW (3 used in this step) www.sauder.com/services 419956 Page 25...
  • Página 26 Step 21 Fasten the LEFT PANEL (AA) to the RIGHT PANEL (Z). å Tighten three HIDDEN CAMS. Page 26 419956 www.sauder.com/services...
  • Página 27 Fasten two CONNECTOR PLATES (14G) to the TOP (X). å Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). SILVER 1-1/8" FLAT HEAD SCREW (4 used in this step) BLACK 9/16" LARGE HEAD SCREW (8 used in this step) www.sauder.com/services 419956 Page 27...
  • Página 28 NOTE: Be sure the WOOD DOWELS insert into the holes in å Fill the holes 1/4 to 1/2 full with GLUE. the TOP. Caution Inspect the parts thoroughly before assembling. Disassembly of glued parts is extremely diffi cult. Page 28 419956 www.sauder.com/services...
  • Página 29 Fasten the RETURN TOP (Y) to the TOP (X). Use eight å BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the MODESTY PANEL (O) to the RETURN TOP (Y). å Tighten the TWIST-LOCK® FASTENER. BLACK 9/16" LARGE HEAD SCREW (8 used in this step) www.sauder.com/services 419956 Page 29...
  • Página 30 Step 25 Fasten the RIGHT MODESTY PANEL (O) to the å RIGHT UPRIGHT (D). Use three BLACK 1-15/16" FLAT HEAD SCREWS (113S). 113S BLACK 1-15/16" FLAT HEAD SCREW (3 used in this step) Page 30 419956 www.sauder.com/services...
  • Página 31 UPRIGHT (N) and the CABINET LEFT (40AX) to the LEFT UPRIGHT (U). Use four GOLD 5/16" FLAT HEAD SCREWS (3S). Roller end GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Finished edge Roller end Finished edge www.sauder.com/services 419956 Page 31...
  • Página 32 TOP (X) as shown. KEYBOARD ON THE LEFT Follow the upper diagram to fasten your å KEYBOARD (M) on the right side or the lower diagram to fasten your KEYBOARD (M) to left side. KEYBOARD ON THE RIGHT Page 32 419956 www.sauder.com/services...
  • Página 33 Fasten the LEFT KEYBOARD UPRIGHT (U) to the TOP (X) å and the RIGHT KEYBOARD UPRIGHT (N) to the RETURN TOP (Y). Tighten four TWIST-LOCK® FASTENERS. KEYBOARD ON THE RIGHT The CABINET RAILS should be facing each other. www.sauder.com/services 419956 Page 33...
  • Página 34 NOTE: The CORD CLIP is used to hold your keyboard cord against å the KEYBOARD SHELF. Roller end Roller end This hole must be closer to this edge. BROWN 1" FLAT HEAD SCREW (4 used in this step) Page 34 419956 www.sauder.com/services...
  • Página 35 Step 30 Fasten two HINGES (14H) to the DOOR (BB). Use four å BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (4 used in this step) www.sauder.com/services 419956 Page 35...
  • Página 36 Fasten a KNOB SET (136K) to the DOOR (BB). Use a BLACK 1-1/8" å MACHINE SCREW (21S). Hinge Push the DOOR STOP (4I) into the RIGHT UPRIGHT (D). å See the next step for DOOR adjustments. å 136K BLACK 1-1/8" MACHINE SCREW (1 used in this step) Page 36 419956 www.sauder.com/services...
  • Página 37 Tighten the screws after making adjustments. To adjust the DOOR in or out (depth), loosen the mounting å screw one turn and move the DOOR in or out, as needed. Tighten the mounting screw after making adjustments. www.sauder.com/services 419956 Page 37...
  • Página 38 Fasten the LARGE DRAWER BACK (D78) to the LARGE DRAWER SIDES (D28 å and D29). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). NOTE: Be sure the LARGE DRAWER BOTTOM (D707) inserts into the groove å of the LARGE DRAWER BACK (D78). Page 38 419956 www.sauder.com/services...
  • Página 39 Fasten the SMALL DRAWER BACK (D109) to the SMALL DRAWER SIDES (D24 and D25). Use two BLACK 1-9/16" FLAT å HEAD SCREWS (30S). NOTE: Be sure the SMALL DRAWER BOTTOM (D716) inserts into the groove of the SMALL DRAWER BACK (D109). å Repeat this step for the other SMALL drawer. å www.sauder.com/services 419956 Page 39...
  • Página 40 SLIDE. Open end Screw head - turn CAM to line up holes in the SLIDES with holes in DRAWER SIDES Open end (4 screws per drawer) GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Page 40 419956 www.sauder.com/services...
  • Página 41 Fasten a KNOB SET (136K) to the LARGE DRAWER FRONT (W). Use one å BLACK 1-1/8" MACHINE SCREW (21S). Insert the FILE RODS into the holes in the FILE GLIDES depending on your fi le sizes. 136K BLACK 1-1/8" MACHINE SCREW (1 used for the KNOB SET) www.sauder.com/services 419956 Page 41...
  • Página 42 BLACK 1-1/8" MACHINE SCREW (2 used for the KNOB SET) (2 screws per drawer) (2 screws per drawer) BLACK 1-9/16" FLAT HEAD SCREW GOLD 5/16" FLAT HEAD SCREW (4 used in this step) (4 used in this step) Page 42 419956 www.sauder.com/services...
  • Página 43 Place the roller on the SLIDE Black tab behind the roller on the RAIL. 70 lbs. (4 used) 50 lbs. 20 lbs. 20 lbs. 25 lbs. BOTTOM 35 lbs. 40 lbs. (3 used) To cover HIDDEN CAMS www.sauder.com/services 419956 Page 43...
  • Página 44 #4. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. Page 44 419956 www.sauder.com/services...

  • Página 45: Liste De Pièces

    Modèle 419956 Bureau en L Utilisez les instructions d’ a ssemblage en français avec les NOUS SOMMES LA POUR VOUS AIDER! schémas étape par étape du manuel d’instruction en anglais. Nous faisons de notre mieux pour nous assurer que votre meuble Chaque étape en français correspond à...
  • Página 46 VOILE DE FOND. Pour commencer l'assemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (12F) dans les gros trous des EXTRÉMITÉS (A et B). REMARQUE : Ne pas trop serrer les VIS. Répéter cette étape pour les DESSOUS (C), les MONTANTS (D et E), les Enfi...
  • Página 47 REMARQUE : Pour chaque GLISSIÈRE D'EXTENSION LARGE, faire tourner une VIS dans le trou indiqué dans le schéma agrandi. Ensuite, Le Bureau en L 419956 est conçu pour maintenir le Surmeuble 419958. enfi ler la cartouche interne de la GLISSIÈRE D'EXTENSION LARGE vers Il y a deux possibilités pour monter le Surmeuble au Bureau en L comme...
  • Página 48 TABLETTE DE CLAVIER SUR LA DROITE Fixer le MONTANT GAUCHE DE TABLETTE DE CLAVIER (U) au DESSUS (X) et le MONTANT DROIT DE TABLETTE DE CLAVIER (N) au DESSUS DE RETOUR (Y). Serrer quatre FIXATIONS TWIST-LOCK®. Page 48 419956 www.sauder.com/services...
  • Página 49 Serrer les vis après avoir ajusté. Pour ajuster la PORTE vers l'intérieur où vers l'extérieur (profondeur), desserrer la vis de montage un tour et déplacer la PORTE vers l'intérieur ou vers l'extérieur. Serrer la vis de montage après avoir ajusté. www.sauder.com/services 419956 Page 49...
  • Página 50 REMARQUE : Prière de lire les informations importantes sur la sécurité fi gurant sur les pages arrière du manuel d’instructions. Ceci complète l'assemblage. Nettoyer à l’ a ide d’une encaustique pour meubles ou d’un chiff on humide. Essuyer. Page 50 419956 www.sauder.com/services...

  • Página 51: Lista De Partes

    Modelo 419956 Escritorio en L Use estas instrucciones de ensamblaje en español junto con las ESTAMOS AQUI PARA AYUDAR! fi guras paso-a-paso provistas en el folleto inglés. Cada paso Tratamos de asegurar que su mueble llega en condición excelente. en español corresponde al mismo paso en inglés. Se destacan Nuestros representantes de Servicio al Cliente son amables y las fi...
  • Página 52 VELO DE FONDO. Para comenzar el ensamblaje, empuje un SUJETADOR TWIST-LOCK® SAUDER (12F) dentro de los agujeros grandes de los EXTREMOS (A y B). NOTA: No apriete los TORNILLOS en exceso. Repita este paso para los FONDOS (C), los PARALES (D y E), los VELOS Deslice las MOLDURAS DE VELO DE FONDO LARGO (L) sobre los DE FONDO (G y O) y los PARALES DE ESTANTE DE TECLADO (N y U).
  • Página 53 Organizador 419958. NOTA: Las CORREDERAS DE EXTENSIÓN ANCHAS se utilizarán más El Escritorio en L 419956 está diseñado para acomodar el Organizador tarde para los CAJONES GRANDES. 419958. Existen dos opciones para fi jar el Organizador al Escritorio en L como se muestra.
  • Página 54 PANEL SUPERIOR DE MESA AUXILIAR (Y) o PANEL SUPERIOR (X) come se muestra. Siga el diagrama superior para fi jar el ESTANTE DE TECLADO (M) al lado derecho o el diagrama inferior para fi jar el ESTANTE DE TECLADO (M) al lado izquierdo. Page 54 419956 www.sauder.com/services...
  • Página 55 PEQUEÑO (D24 y D25). Utilice dos TORNILLOS NEGROS DE CABEZA PERDIDA de 40 mm (30S). NOTA: Asegúrese que el FONDO DE CAJÓN PEQUEÑO (D716) ajuste dentro de la ranura del DORSO DE CAJÓN PEQUEÑO (D109). Repita este paso para el otro cajón PEQUEÑO. www.sauder.com/services 419956 Page 55...
  • Página 56 NOTA: Por favor, lea las páginas de atrás del folleto de instrucciones en cuanto a importante información de seguridad. Esto completa el ensamblaje. Limpie con su pulimento para muebles preferido o un paño húmedo. Seque con un paño. Page 56 419956 www.sauder.com/services...
  • Página 57 à Les téléviseurs peuvent être particulièrement un téléviseur. cet eff et. lourds. De plus, le poids et l’emplacement du tube image ont tendance à rendre les téléviseurs instables et enclins à tomber vers l’ a vant. www.sauder.com/services 419956 Page 57...
  • Página 58 Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y propensa a volcarse hacia adelante. Page 58 419956 www.sauder.com/services...

  • Página 59: Garantie Limitée De 5 Ans

    à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
  • Página 60 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.

Tabla de contenido