Babyauto Vivitta VIK V2 123 Manual De Uso

1. You can change the position of the harness straps
by pulling them out of the strap slots (I) and
inserting them into another one that best fits your
child's height. (Fig. 3.1, Fig. 3.2 and Fig. 3.3).
2. Place the child restraint system on the vehicle
seat, making sure it is properly pressed against the
vehicle seat back (Fig. 3.4).
3. Insert the vehicle belt through the guides (H)
(Fig. 3.5 and Fig. 3.6).
4. Pass the abdominal belt through the guide (F) under
the armrest (Fig. 3.7). Pass the diagonal belt over the
armrest. Fasten the seat belt at the anchor point of
the vehicle (Fig. 3.8). You will hear a "click" when it´s
properly installed.
5. Check that the seat belt has not twisted or tangled.
Finish tightening the vehicle seat belt by pulling the
diagonal belt up until there is no slack and the child
seat is firmly installed (Fig. 3.9).
6. Open the harness by pressing the buckle button (G).
7. Place the child in the child restraint seat (Fig. 3.10).
Depending on the child's height, the headrest can be
adjusted up or down (Fig. 3.11).
8. Fasten the harness by joining the metal connectors
and inserting them into the buckle (G), you will hear
a click that will indicate that the harness buckle is
correctly connected. (Fig. 3.12, Fig. 3.13 and Fig. 3.14).
9. To adjust the harness straps to the child's body,
pull the harness strap adjusters (C). (Fig. 3.15).
4. INSTALLATION. GROUP 23
Use Group 2 & 3 only from
NOTICE
approx. 4 to 12 years of age
(15-36 kg)
1. Remove the harness straps (E) from the backrest
and base (Fig. 4.1 and Fig. 4.2).
2. Remove the harness (G) from the seat (Fig. 4.3 and
Fig. 4.4).
3. Pass the diagonal section of the vehicle belt through
the guide (B) located on the headrest (Fig. 4.5).
4. Place the child in the seat and connect the belt to
the vehicle anchor point by passing it through the
abdominal belt guides (F) a (Fig. 4.6).
5. Always check that the vehicle belt is suitable for your
child's height. The child's shoulders should always
be just below the backrest slots at a suitable height
(Fig.4.7 and Fig. 4.8).
5. CLEANING AND MAINTENANCE
Cleaning the seat
1. Wash the straps and plastic parts with neutral
detergent and warm water.
2. Ensure that no soap enters the buckle or metal parts.
3. Do not use chemicals or bleach on any part of the
seat.
4. Dry thoroughly before use.
WASHING INSTRUCTIONS:
· The cover is removable and washable at 30º. Dry in
the fresh air only.
· Wash in washing machine (cold).
· Do not use bleach.
· Dry clean, with any solvent except trichloroethylene.
· Do not use dryer.
· Do not iron.
30°C
If you have any doubts or queries regarding the
use or placement of this product or you need any
replacement elements, please contact our Customer
Services Department.
6. GUARANTEE
This product is covered by a legal warranty under
the terms and conditions in Royal Legislative
Decree 1/2007, from the 16th of November. For a
period of 2 years after the date of purchase, any
lack of conformity existing at the time of delivery
of the product is covered. It is essential to keep
the purchase ticket or invoice proving the purchase
of the product within the warranty period. The
instructions for use given in the product manual
must be followed carefully for its start-up, as well
as for the subsequent and proper operation of
the product. This warranty does not cover defects
arising from accidental deterioration, misuse, abuse
of the product, improper maintenance, or repair by
unauthorised technical personnel or service, in which
case the user shall bear the costs of delivery and,
where applicable, the repair. The warranty does not
cover consumable components, such as batteries or
coatings exposed to wear and tear, that are the result
of normal use of the product.
VIK V2 123
Grupo · Group:
1 2 3
Apto para
Suitable for
—
9 - 36 kg
MANUAL DE USO
INSTRUCTIONS MANUAL