Programas Asociados Con Los Textos De Las Pantallas - Fagor CNC 8037 MS Manual De Sustitución

Tabla de contenido

Publicidad

%PANTALLA 1,MX,
;(PRGSCRIPT 1)
;(DEBUG)
;(DISABLE 1)
;(DISABLE 20)
;(AUTOREFRESH W1=PLCR101)
3.
;(AUTOREFRESH W3=PLCR103)
;(AUTOREFRESH W6=PLCR120)
;(AUTOREFRESH W10=PLCR107)
;(AUTOREFRESH W11=PLCR109)
;(AUTOREFRESH W12=PLCR110)
;(AUTOREFRESH W13=PLCR111)
;(AUTOREFRESH W15=PLCR113)
;(AUTOREFRESH W16=PLCR114)
;(AUTOREFRESH W17=PLCR116)
;(AUTOREFRESH W18=PLCR117)
;(AUTOREFRESH W19=PLCR119)
;(AUTOREFRESH W20=PLCR121)
;(AUTOREFRESH W21=PLCR123)
;(UNMODIFIED AUTOREFRESH W40=PLCR107)
;(UNMODIFIED AUTOREFRESH W41=PLCR109)
;(UNMODIFIED AUTOREFRESH W42=PLCR110)
;(UNMODIFIED AUTOREFRESH W43=PLCR111)
;(UNMODIFIED AUTOREFRESH W45=PLCR113)
;(UNMODIFIED AUTOREFRESH W46=PLCR114)
;(UNMODIFIED AUTOREFRESH W47=PLCR116)
;(UNMODIFIED AUTOREFRESH W48=PLCR117)
;(UNMODIFIED AUTOREFRESH W49=PLCR119)
;(UNMODIFIED AUTOREFRESH W50=PLCR121)
;(UNMODIFIED AUTOREFRESH W51=PLCR123)
;(UNMODIFIED AUTOREFRESH W60=PLCR304)
;(END)
3.2.2
CNC 8037
M
·MS· & ·TS·
ODELOS
·86·
P999001(001.WGD)
Estos programas quedan reservados para el propio CNC y no deben ser borrados. No
pueden ser utilizados como programas pieza por el usuario ya que tienen un significado
especial.

Programas asociados con los textos de las pantallas

El programa de textos que utiliza la aplicación está creado en el fichero MsgFile.txt.
El mencionado fichero se copiará como:
012345.PIM (CNC 8037 MS)
012345.PIT (CNC 8037 TS).
Si se desea disponer de textos y mensajes se seleccionará el p.m.g. MSGFILE (P131) con
el número de programa 12345.
El programa 12345 (MSGFILE) podrá estar en memoria de usuario o en el disco duro
(KeyCF). Si está en los dos sitios se toma el de memoria de usuario.
A continuación se muestra la estructura del programa 12345 (MSGFILE) según si el modelo
es MS o TS:
CNC 8037TS
P999002(002.WGD)
%PANTALLA 2,MX,
;(PRGSCRIPT 1)
;(DEBUG)
;(DISABLE 1)
;(DISABLE 20)
;(AUTOREFRESH W1=PLCR125)
;(UNMODIFIED AUTOREFRESH W2=PLCR125)
;(UNMODIFIED AUTOREFRESH W4=PLCR125)
;(AUTOREFRESH W10=PLCR126)
;(AUTOREFRESH W11=PLCR128)
;(AUTOREFRESH W12=PLCM150,1)
;(AUTOREFRESH W13=PLCM151,1)
;(AUTOREFRESH W14=PLCM152,1)
;(AUTOREFRESH W15=PLCR142)
;(UNMODIFIED AUTOREFRESH W40=PLCR126)
;(UNMODIFIED AUTOREFRESH W41=PLCR128)
;(UNMODIFIED AUTOREFRESH W42=PLCM150,1)
;(UNMODIFIED AUTOREFRESH W43=PLCM151,1)
;(UNMODIFIED AUTOREFRESH W44=PLCM152,1)
;(UNMODIFIED AUTOREFRESH W45=PLCR142)
;(END)
M a n ua l d e s us t i tu c ió n

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Cnc 8037 ts

Tabla de contenido