Loading The Tool - Stanley Bostitch GFN1564K Manual De Instrucciones

2. Insert the fuel cell into the tool
i. Push up and pull out the actuater (Fig. 6).
ii. Insert the fuel cell into the tool (Fig. 7), making sure
that the stem of the fuel cell lines up correctly with the
hole in the adaptor (Fig. 8).
iii. Close the actuater (Fig. 9).

5. LOADING THE TOOL

CAUTION: When loading nails into tool:
● Do not depress trigger
● Do not depress contact arm
● Keep your face, hands, feet and other body parts,
as well as those of other persons away from the
nose to avoid possible injury during loading.
MODELS: GFN1664K / GFN1564K
1. Insert a nail strip into the rear of the magazine (Fig. 10).
2. Slide the nail strip forward in the magazine (Fig. 11).
3. Pull the nail feeder past the nail strip towards the rear
of the magazine (Fig 12) to engage it on to the nail strip.
Note: Nail strips of more than 10 nails must be used.
4. The nailer is now ready to operate.
Removing the nails:
1. Pull the nail feeder to the back of the magzine slightly
and depress the button located in the feeder. (Fig. 13).
2. Gently slide the nail feeder forwards, over the nail
strip.
3. Slide the nails to the back of the magazine and remove.
(Fig. 14).
MODEL: GBT1850K
1. Press the latch on the back of the magazine and pull
back the cover. (Fig. 15)
2. Set the nail strip into the magazine, keeping the points
of nails in contact with groove at the base of the
channel. (Fig. 16)
3. Slide the nail strip to the front of the magazine into the
blade guide. (Fig. 17)
4. Push the cover forwards to close the magazine.
● Always keep the points of nails in contact with
Groove.
● Use nail strip of more than 5 nails.
4. The Nailer is now ready to operate.
All manuals and user guides at all-guides.com
Removing the nails:
1. Lightly press the stop lever and gently pull out the
magazine cover.
2. Remove the nails from the nailer.
CAUTION: To prevent unintentional operation, never
touch the trigger or place the top end of the contact arm
on a work bench on floor. Also, never face the nail outlet
toward any part of a person.
6. USING THE NAILER
CAUTION
● Squeeze the contact arm when drivng a nail,
● Using the tool for an extended period may lead to oil
● To ensure that the material to be nailed stays clean,
CYCLE RATES
These tools are designed to operate up to the following
cycle rates:
Intermittent Operation – 2 to 3 nails per second
Continuous Operation – 1000 nails per hour
Exceeding these rates could cause the tool to overheat,
resulting in loss of performance or damage to tool
components. By using the nailer at its recommended
cycle rate, you will be able to drive several thousand
nails in a typical working day.
SAFETY TRIP
These tools are supplied fitted with a sequential safety
trip and are marked with an inverted equilateral triangle
(▼). Do not attempt to use a tool marked in this way if
the safety trip is missing or appears damaged.
The sequential trip requires the operator to hold the tool
against the work with the safety trip depressed before
pulling the trigger. In order to drive additional fasteners,
the trigger must be released and the tool lifted away
from the work, before repeating.
This makes accurate fastener placement easier, for
instance on framing, toe nailing and crating applications.
The sequential trip allows exact fastener location
without the possibility of driving a second fastener on
recoil. The sequential trip tool has a positive safety
advantage because it will not accidentally drive a
fastener if the tool is contacted against the work or
anything else, while the operator is holding the trigger.
otherwise the piston can not return correctly.
around the exhaust outlet or nose, resulting in
spattering.
wipe off any oil that gets on the tool.