Presetting Tv Programmes Using The Epg; Using Auto Channel Select And Standby Recording - Pioneer PDP-505XDE Manual Del Usuario

02 Using Electronic Programme Guide (EPG) (for DTV only)
Presetting TV programmes using the
EPG
Using the EPG, you can easily preset digital TV programmes
for watching (auto channel select) and recording later.
You must also adjust your recording equipment settings to
record the programme. Refer to the operation manual
provided with your recording equipment.
Using auto channel select and standby record-
ing
With the power to the system left on, this function automati-
cally selects a preset TV programme when its on-air time
comes. That way you will not miss the start of an important TV
programme because you were enjoying another TV
programme.
Even if the system is in standby mode when the preset TV
programme's on-air time comes, the Media Receiver wakes
up and outputs AV signals for recording.
1
Press EPG.
• The EPG screen appears.
2
Select a programme to be preset ( / ,
ENTER).
• Select a programme not yet started.
• A setup menu appears.
• Select a programme currently on-air (then ENTER):
The EPG screen closes and a channel is tuned in.
• Select a programme currently on-air (then GREEN):
The programme can be set for recording/watching the
next time (or week) it is shown.
• Select a programme not yet started (then ENTER or
GREEN): The programme can be set for recording/
watching.
007
**************
***********************
***********************
Sun.12.Sep Sun.12.Sep
**********
****
******
*************
**********
*************
**********
***********
3
A dialogue box for confirmation appears.
Select "Yes" ( /
12
En
All manuals and user guides at all-guides.com
/
11:30 12:00 12:30
**************** ***************** **************
************** **************** *****************
************** ** **************
************************
********************************
**********************
**************** ** ****************
**************** *****************
then ENTER).
4
The Programme Timer screen with a list of other preset
programmes information appears.
Programme Timer
No. Date
01
Mon.05.Jan
02
Every Day
03
Every Sun
04
Mon-Fri
05
Sat, Sun
06
07
08
09
10
• You can modify the presettings here ( / ,
ENTER).
• You can register the presettings here (
5
Press RETURN to return to the EPG screen.
007
**************
***********************
***********************
Sun.12.Sep Sun.12.Sep
**********
then
****
******
*************
**********
*************
**********
***********
• The EPG screen updates with the new presettings.
• A red clock icon appears for the preset programme.
• A yellow triangle icon appears for overlapped
presettings.
6
Press EPG to exit the EPG screen.
With the system switched on, a channel switch alarm
00:00 - 12:00
message appears approximately 60 seconds before
execution and the channel is switched a short time
before the start of the programme.
• Auto channel select is not executed when the system is in
the standby mode.
• Even in the standby mode, preset programmes can be
recorded as only the Media Receiver alone wakes up and
outputs AV signals when the preset time comes.
• Finish presetting operations three minutes before the start
of the programme.
• For priorities about overlapped presettings, see "Priority
rules for overlapped presettings" on page 13.
• The TIMER indicator on the front of the Media Receiver
lights up in orange when a programme is preset for
recording/watching.
• Recording may fail because of watching restrictions
imposed by the CA module.
Wed.24.Nov 12:34
Time Channel
12:00-13:00 001 ************
14:00-15:00 007 ***************
14:00-15:00 007 ***************
14:00-15:00 007 ***************
14:00-15:00 007 ***************
or ENTER).
11:30 12:00 12:30
**************** ***************** **************
************** **************** *****************
**************
************************
********************************
**********************
**************** ****************
**************** *****************
Info
/ then
00:00 - 12:00
**************