Reclining Headrest - CYBEX gold PALLAS S - FIX Manual Del Usuario

RECLINING HEADREST

EN
The reclining headrest (c) helps to prevent the child's head from dangerously
tipping forward during sleep. It can be set to one of 2 positions. Push the
reclining headrest (c) forward until the desired position is reached. To return
it to the original position, the lever (v) must be operated and the headrest
pulled back.
The child's head should always be in contact with the reclining headrest.
��
CORRECT INSTALLATION MODE
Installation mode
Installation
SECURING THE CHILD WITH IMPACT SHIELD – GROUP 1 (9–18 KG)
1. Insert the impact shield (f). The side flaps of the impact shield (f) fit exactly
between the arm rests and seating surface of the booster. Push the central
adjustment button (q) and adapt the impact shield to your child.
2. Pull out the entire length of the vehicle seat belt.
3. Place the lap belt over the designated red belt routing on the impact shield (g).
4. Lock the vehicle seat belt into the belt buckle. It must lock in place with an
audible "CLICK".
5. Tighten the lap belt by pulling the shoulder belt backwards.
6. Feed the shoulder belt in parallel with the lap belt back into the belt routing
(g) and pull the shoulder belt tight. Ensure that both parts of the belt cover
the entire width of the impact shield (f) in the belt routing (g).
7. Feed the shoulder belt tightly through the belt routing of the impact shield (g)
until it is clamped inside the belt guide.
8. Put the shoulder belt between headrest (c) and backrest (b). The shoulder
belt does not need to be guided through the shoulder belt guide (i).
8
Group 1: 9 ‒ 18 kg Group 2/3: 15 ‒ 36 kg
with base and without base and
impact shield impact shield
ADJUSTING THE LYING POSITION (9-18 KG)
1. To put the seat in the lying position, press the position adjustment button (r).
2. To return the seat from the lying position to the sitting position, press the
position adjustment button (r) again and guide the seat upwards with light
pressure against the booster (e).
The lying position is only available for group 1 (9-18 kg).
��
SWITCH FROM GROUP 1 TO GROUP 2/3
1. Remove the impact shield (f), as soon as your child weighs 18 kg.
Switching from group 1 to group 2/3 is not permitted if your child weighs
��
less than 15 kg. Keep the impact shield in a safe and secure place.
2. Press the two release buttons of the base (t) on the underside of the booster
(e) and pull it away from the base (s) until there is some resistance.
3. Press the position adjustment button (r) and pull the seat away from the
base (s) completely.
4. Operate the ISOFIX-Connect-adjustment handle (l) and pull the two ISOFIX-
Connect-locking arms (k) out.
5. Keep the ISOFIX-Connect-adjustment handle (l) held and release the two
snap clips (u) on the underside of the booster (e), one after the other and
pull the ISOFIX-Connect loking arms (k) out of the base. If necessary, use
a screwdriver.
6. Push the ISOFIX-Connect-locking arms (k) into the designated openings on
the underside of the booster (e) until there is some resistance.
7. Operate the position adjustment button (r) on the underside and push the
ISOFIX-Connect-locking arms (k) as far in as possible.
Note the minimum drop height of the ISOFIX-Connect-locking arms.
��
Ensure that the locking arms (k) are installed the right way around and that
��
the teeth of the locking arms are up.
When reassembling the seat, proceed in precisely the reverse order. Use
��
the instructions to check beforehand if all parts are present.