Error Messages - Sony SRX-R110 Manual De Instalación

Error Messages

The error messages are displayed in the STATUS MESSAGE window on the left side of projector and the Error display
window of the SRX Controller. If there are two or more messages, a displayed message changes each 5 seconds.
No. Error messages
1 INPUT-A POWER ALERT
2 INPUT-B POWER ALERT
3 INPUT-C POWER ALERT
4 INPUT-D POWER ALERT
5 PR-284_1 POWER ALERT
6 PR-284_2 POWER ALERT
7 PR-284_3 POWER ALERT
8 PR-284_4 POWER ALERT
9 24V POWER SUPPLY ALERT
10 16V POWER SUPPLY ALERT
11 PR-284_1 DETACHED
12 SXRD PANEL TEMPERATURE
ALERT
13 LAMP_A FAN ALERT
14 LAMP_B FAN ALERT
15 LAMP_A POWER SUPPLY UNIT
FAN ALERT
16 LAMP_B POWER SUPPLY UNIT
FAN ALERT
17 PR-284 FAN FAILURE
18 OPTICAL UNIT TEMPERATURE
ALERT
19 LAMP_A TEMPERATURE ALERT
20 LAMP_B TEMPERATURE ALERT
21 LAMP_A HOUSE DETACHED
Meaning
Trouble with power of INPUT A board Replace the INPUT A board.
Trouble with power of INPUT B board Replace the INPUT B board.
Trouble with power of INPUT C board Replace the INPUT C board.
Trouble with power of INPUT D board Replace the INPUT D board.
Trouble with power of PR-284 board
at the top
Trouble with power of PR-284 board
on the second row
Trouble with power of PR-284 board
on the third row
Trouble with power of PR-284 board
on the fourth row
The projector has failed to supply 24V
power.
The projector has failed to supply 16V
power.
The PR-284 board is not attached
correctly on the top row.
The temperature of the panels is too
high.
Trouble with the fan for Lamp A, or
the harness is disconnected or down.
Trouble with the fan for Lamp B, or
the harness is disconnected or down.
Trouble with the fan for Lamp A
power (ballast), or the harness is
disconnected or down.
Trouble with the fan for Lamp B
power (ballast), or the harness is
disconnected or down.
Trouble with the fan for PR-284 board,
or the harness is disconnected or
down.
The temperature of the optical unit is
too high, or the harness is
disconnected or down.
The temperature of Lamp A is too
high, or the harness is disconnected or
down.
The temperature of Lamp B is too
high, or the harness is disconnected or
down.
The projection lamp house of Lamp A
is detached, or the harness is
disconnected or down.
Remedy
Replace the corresponding PR-284 board.
Replace the corresponding PR-284 board.
Replace the corresponding PR-284 board.
Replace the corresponding PR-284 board.
Overload on the 24 V line. Replace the AC inlet
on the projector.
Overload on the 16 V line. Replace the AC inlet
on the projector.
Attach the PR-284 board on the top row correctly.
Check the panel cooling fan or the ventilation
holes for intake.
Check the connection of the Lamp A fan, or
replace the fan.
Check the connection of the Lamp B fan, or
replace the fan.
Check the connection between the Lamp A power
and the SY board, or replace the fan for Lamp A
power.
Check the connection between the Lamp B power
and the SY board, or replace the fan for Lamp B
power.
Check the connection between the fan located on
the side of the board shield and the SY board, or
replace the fan.
The ventilation hole for intake on the projector
may be blocked. Check the projector is installed
properly.
The ventilation hole for intake on the projector
may be blocked. Check the projector is installed
properly.
The ventilation hole for intake on the projector
may be blocked. Check the projector is installed
properly.
Check the attachment screw on the projection
lamp house of Lamp A or the harness.
31
GB
Error Messages