Operation - SPARKY BR 100E Instrucciones De Uso

Operation

This power tool is supplied from single-phase alternat-
ing current mains only. It is double insulated according to
EN 60745, IEC 60745 and can be connected to
grounded or not grounded sockets. This power tool is
radio suppressed in compliance with EMC Directive
2004/108/EC.
This power tool is designed for drilling in steel, wood,
plastics, etc.
PRIOR TO INITIAL OPERATION
WARNING: Make sure the power supply volt-
age corresponds to the value indicated on the name
plate with technical data of the appliance.
▪ Always check the position of ON/OFF switch. The
power tool must be connected to the power supply
socket only when this switch is in OFF position. If the
plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
▪ Make sure the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
WARNING: Prior to operation always check
the direction of rotation. Shift the reversing switch
only when the spindle has come to a complete stop.
Reversing prior to final spindle halt may damage the
power tool.
INSTALLING AND REMOVING BITS
WARNING: Switch off and unplug the ma-
chine prior to any procedure on the power tool.
Grip rear collar of keyless chuck and rotate front collar
until chuck is opened sufficiently for the bit to be inserted.
Then firmly tighten front collar by hand.
SWITCHING ON / SWITCHING OFF
Brief activation:
▪ Switching on: Press ON/OFF switch (8).
▪ Switching off: Release ON/OFF switch (8).
Continuous use:
▪ Switching on: Press ON/OFF switch (8) and in
pressed position lock it by button (9).
▪ Switching off: Press ON/OFF switch (8) once and
release it immediately.
6
EN
WARNING: Before plugging in the tool, al-
ways check to see that the trigger switch (8) actuates
properly and returns to OFF position when released.
SMOOTH ELECTRONIC RPM CONTROL
Light pressure on ON/OFF switch (8) results in low rota-
tion speed, further pressing the switch results in smooth
increase of the rpm to maximum upon reaching the ex-
treme position.
SELECTION OF RPM VALUE
The necessary speed can be pre-selected by rotating
the regulator dial (7) clockwise or anti-clockwise.
REVERSING
The extreme position of lever (6) to the right is equivalent
to clockwise rotation, the extreme position to the left – to
anti-clockwise rotation. When the ON/OFF switch (8) is
depressed lever (6) can not be actuated. Reversing can
be performed only when the spindle is not rotating!
SCREWING / UNSCREWING BOLTS,
SCREWS AND NUTS
Following the above-described procedure, tighten the
corresponding accessory in chuck (2). Select the rota-
tion direction necessary by lever (6). These operations
must be performed only at low rpm.
WARNING: In case of screwing / unscrewing
long bolts and screws there is a danger of slipping the drill.
REMOVING THE CHUCK
Grip rear collar of keyless chuck (2) and rotate front collar
until chuck is opened. By means a screwdriver unwind
the left-treaded securing screw. Insert and fasten Allen
key or screwdriver bit into the chuck.
Clamp the place for fixing the spindle (3) by means of a
spanner and rotate the chuck anti-clockwise by the free
end of the key (bit).
RECOMMENDATIONS FOR OPERATION
Drill at speed lower than the maximum speed and select
the speed depending on the processed material.
Use straight shank drill bits.
Watch out the stage of blunting of the bit and replace it if
considerable decrease of efficiency is observed.
Before drilling large-diameter holes in metal, wood or
plastics, drill a small pilot hole.
ACCESSORIES TO BE USED WITH
THIS POWER TOOL
▪ Drill bits for metal Ø0.8 to Ø10 mm.
▪ Drill bits for wood Ø0.8 to Ø20 mm.
▪ 6.35 mm (1/4") hexagon shank screwdriver bits.
BR 100E • BR 101E