GGP Sweden XM 130 Instrucciones De Uso página 48

All manuals and user guides at all-guides.com
EN
2.3 BATTERY
See 6.8
2.4 SEAT
NOTE! To facilitate installation of the seat, ap-
ply a drop of oil to the four screws before screw-
ing them into the seat.
Release the catch (2:S) and fold up the seat
bracket.
Install the mounting in the rear (upper) holes as
follows:
1. Install the shoulder washers (1:F) on the screws
(1:G).
2. Insert the screws through the slots in the
bracket. Place a washer (1:I) between the seat
and the bracket.
3. Tighten the screws in the seat. Tightening
torque: 9±1.7 Nm.
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
4. Check that the seat moves easily in the slots in
the bracket.
Install the mounting in the front (lower) holes as
follows:
1. Install the screw knobs (1:H) on the screws
(1:G).
2. Install a washer (1:I) on each screw.
3. Insert the screws through the slots in the bracket
and tighten by hand in the seat.
4. Fold the seat down and place it in the desired
position.
5. Tighten the screw knobs (1:H) by hand.
The screw knobs (1:H) and the seat will
be damaged if tools are used.
The seat can be folded. If the machine is parked
outside when it is raining, fold the seat forward to
protect the seat cushion from getting wet.
The seat is locked. To fold the seat up or down,
release the catch (2:S).
2.5 STEERING WHEEL
In order to minimise the axial play in the steering
column, the shim washers (4:K) and/or (4:L) must
be installed on the steering column between the
steering column jacket and the bracket as follows.
1. Install the steering column jacket on the
steering column and secure by knocking in the
tension pin (4:J) approximately 1/3 of its length.
2. Pull the steering column jacket and the steering
column up.
48
ENGLISH
3. From the outside, check whether no washers,
the 0.5 mm washer, the 1.0 mm washer or both
washers can be inserted into the gap. The
washer/washers must not be forced in, as there
must be a little axial play.
4. Pull out the cotter pin and dismantle the steering
wheel jacket.
5. Install the washer/washers in accordance with
point 3 above.
6. Install the steering column jacket on the
steering column and secure by knocking in the
tension pin fully. Use a counterhold.
The steering wheel should be installed so that the
steering wheel boss is in the "10 o'clock position" .
2.6 TOWING HITCH
Screw the towing hitch (5:A) into the two holes on
the underside of the rear axle using screws (5:B).
Tighten the screws properly.
Tightening torque: 22 Nm.
2.7 DECK MOUNT
This only describes installation on the right-hand
axle. The same procedure must be carried out on
the left-hand axle.
1. Remove the circlip (1:M) and the outer washer
(1:N).
2. Install the deck mount (1:O).
The washer (1:N) with an inner lug
must always be placed against the
circlip. Otherwise there is a risk of the
circlip coming loose.
3. Install the outer washer (1:N) and the circlip
(1:M).
4. Lubricate the deck mount's lubricating cup
using a grease gun until grease penetrates along
side the axle.
The screws (1:P) and the nuts (1:Q) must be used
to install the work tool in the deck arms (5:O).
2.8 TYRE PRESSURE
Check the air pressure in the tyres. Correct air
pressure:
Front: 0.4 bar (6 psi)
Rear: 1.2 bar (17 psi)
2.9 ACCESSORIES
For the installation of accessories, see separate
installation guide supplied with each accessory.
Note: The cutting deck is regarded as an accessory
here.