Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Wheel height adjustment (fig. G & H)
Your mower features the Black & Decker One-Touch Wheel-
Height adjustment system. This system will adjust all four
wheels at the same time.
The mower has eight blade height adjustment positions
(25 mm to 82 mm). Refer to the scale and pointer at the front
of the mower. The pointer will indicate the height setting for
cutting your lawn. This setting can be a reference for the next
time you want to cut your lawn to the same height.
Release the bail bar (2) to turn the lawnmower off, wait
until the blade stops and remove the safety key (1).
To raise or lower the cutting height, place the palm of
your hand on the palm rest (15) and with your fingers,
squeeze upward on the finger grip (16) and hold.
While holding the finger grip (16), raise or lower the
cutting height as required.
When the mower is at the required height, hold it in
place with your left hand on the lower right handle bar
and release the finger grip (16) to lock the height
adjustment.
Note: To make sure that the mower is securely locked in one
of the eight positions, press down on the palm rest after
releasing the finger grip.
Removing the battery (fig. I)
The battery pack (6) can be removed from the mower for
storage/charging or left in the mower for charging.
Before removing the battery:
Place the mower on level ground.
Release the bail bar (2) to turn the mower off, wait for
the blade to stop and remove the safety key (1).
To remove the battery:
Lift the lever (8), and then rotate it back away from the
battery pack to un-latch the clasp (9). Lift the battery
pack out.
Before installation of the battery pack, make sure that the
mower is clear of debris and the charger connector (20) is
disconnected from the battery pack (6).
Charging the battery (fig. J - L)
Note: Charge the battery before first use.
The battery can either be removed from the mower for
charging or can be charged while in place.
Release the bail bar (2) to turn the lawnmower off, wait
until the blade stops and remove the safety key (1).
Align the green (+) and white (-) connectors and insert
the charger plug (20) into the receptacle (17) on the
mower or remove the battery and insert the charger
plug (20) into the receptacle (19) on the battery.
The charger connector (20) can only be plugged into the
mower receptacle one way.
10
Insert the 240 Volt plug of the charger into a mains
power socket (fig. L).
The red light (21) on the charger (22) will come on to
indicate that the battery is being charged. If the red light
is not on, check that the charger connector is aligned
correctly.
When charging is complete the red light (21) will go off
and the green light (23) will come on.
It will take approximately 12 hours to charge a fully
discharged battery.
It is recommended to leave the battery on permanent charge
between uses for optimum performance during the mowing
season.
The charger supplied with this product is intended to be
plugged in such that it is correctly orientated in a vertical or
floor mount position.
Use
Warning! Let the appliance work at its own pace. Do not
overload.
Safety key
Remove the safety key:
Whenever leaving the appliance unattended.
Before cleaning a blockage.
Before checking, cleaning or working on the appliance.
After striking a foreign object.
Whenever the appliance starts vibrating abnormally.
Switching on and off
Warning! Sharp moving blade. Never attempt to override
the operation of this switch and safety key system as a
serious injury could result.
Switching on (fig. M & N)
Insert the safety key (1) fully into the switch housing.
Push the button (24) on the side of the switch housing.
Pull the bail bar (2) toward the handle bar (3).
Switching off (fig. M & N)
To turn the lawnmower off, release the bail bar (2).
When the bail bar (2) has returned to the original position it
will activate the automatic braking mechanism. The motor is
electrically braked and the lawnmower blade will stop
rotating in 3 seconds or less.
Safety shield and rear door (fig. O)
The safety shield (28) is designed to minimize the throwing
of stones or other objects backward from under the
lawnmower by the blade.
The safety shield (28) and the rear door (25), minimise the
possibility of accidental foot contact with the blade.
Publicidad
Tabla de contenido
