Orbea BLUE PAPER URRUN 2022 Manual Tecnico página 7

12 | ORBEA
BEARINGS: The bearings (bottom bracket, linkage pivot
points, headset, wheels, etc.) are elements subject to wear
that must be inspected on a regular basis to ensure that
they operate correctly. Bearings in poor condition can
damage the components in which they are installed. Ad-
verse weather conditions speed up bearing wear. Bearings
that have excessive play or that do not turn smoothly must
be replaced immediately. In the case of any doubt, consult
your authorized dealer.
Damage to components like the frame, bi-
cycle wheels, etc. associated with the lack
of maintenance and the replacement of the
bearings are not covered by the warranty.
ELECTRIC SYSTEM: Turn the bicycle on and check that
the electric assist system functions correctly. Ensure
there is electric assistance and that all components op-
erate correctly. (motor, display, assist level switch and
speed sensor).
If there is no electric assistance, inspect all the connec-
tions between the components and the condition of the
components and the cables (cables and components that
show damage must be replaced).
Check for errors in the electric system. The SC-EN800 or
SC-E5003 displays will show the error code if there was any.
On models equipped with the Shimano SC-EN800 display,
you can connect the bicycle via Bluetooth to the Shima-
no Etube Project Cyclist mobile app to know more about
the error or warning code and access its troubleshooting
procedure. If the error persists after following the recom-
mended solution or if a solution is not possible to be ap-
plied by the consumer, take your bicycle to an authorized
dealer for a complete diagnosis and repair.
The Shimano SC-E5003 display does not
have Bluetooth connectivity, and therefore
you will not be able to connect the bicycle to
the app on models with this display. To know
the troubleshooting procedure for an error or
a warning, consult the code in the Shimano
STEPS user manual or take your bicycle to
an authorised Shimano dealer to have it di-
agnosed or replace the original display for a
Shimano SC-EM800 display.
TECHNICAL MANUAL
Rear the full Shimano STEPS warning and error code list
and troubleshooting procedure in the following link:
https://si.shimano.com/#/en/iER/STP0A
Failure to follow the recommendations out-
lined in this manual and riding a bicycle that
shows signs of the symptoms described
above may cause accidents and serious
injuries.
TIGHTENING TORQUES. Always check the
tightening torques and install the compo-
nents described in this manual according to
ponents from other manufacturers installed
on your Orbea bicycle. The failure to follow
function of the components, accidents and
even death.
M AI NT EN AN CE S CHEDU LE
O F T HE C OMP ON ENTS
Maintenance periods for the components
indicated below are general guidelines and
largely depend on factors such as weather
conditions in which your bicycle is ridden
(adverse conditions considerably reduce
the life of the components and increase
maintenance frequency), the cleanliness
of your bicycle and its components (com-
ponents with accumulated dirt wear more
quickly), and use (more demanding use
of the bicycle will require more frequent
maintenance periods).
For components from other brands mount-
ed on Orbea bicycles, you can check the
recommended or mandatory maintenance
periods on the manufacturer's website or by
contacting the distributor of that brand in
your country.
B LUE PAP ER U RRU N · 2022
Damage to components as a result of failing
to follow the recommended maintenance pe-
riods could result in damage that is not cov-
ered by the warranty conditions of Orbea or
the component manufacturer.
The failure to comply with maintenance peri-
ods could result in damage to the components
and lead to malfunctions and accidents.
HEADSET:
· Inspection of its operation before each ride.
· Disassembly and manual inspection of the bearings
once every 6 months of use.
-
BOTTOM BRACKET:
-
· Inspection of its operation before each ride
· Disassembly and manual inspection of the bearings
once every 6 months of use.
DRIVETRAIN:
· Inspection of its operation before each ride.
· Regular inspection of chain wear every 500 km. A chain
that is worn beyond the manufacturer's recommenda-
tions must be replaced to prevent damage to the rest
of the drivetrain components. The failure to observe
the manufacturer's recommendations in terms of wear
could necessitate the replacement of the rest of the
parts of the drivetrain.
WHEELS:
· Inspection of its operation before each ride.
· Disassembly and manual inspection of the bearings and
all components once every 6 months.
SHOCKS AND SUSPENSION FORKS:
· Inspection of its operation before each ride.
· Inspection and full maintenance every 125 hours or
rer's authorized dealer.
DROPPER SEAT POSTS:
· Inspection of its operation before each ride.
· Inspection and full maintenance every 125 hours or
rer's authorized dealer.
PIVOT POINTS ON FULL SUSPENSION FRAMES:
· Inspection of its operation before each ride.
· Disassembly of the frame and the manual inspection
of all the bearings every 125 hours of use or once a
ter depending on the conditions in which the bicycle
is ridden. More demanding use of the bicycle or use
in adverse weather conditions or in mud requires the
disassembly and inspection of the frame once every 75
hours of use or once every 6 months (whichever comes
sive play, it must be replaced immediately.
GEAR CABLES AND HOUSING:
· Inspection of its operation before each ride.
· Replacement of gear cables every 6 months to 1 year
depending on the conditions in which the bicycle is used.
BRAKES:
· Inspection of the operation and wear of the brake pads
or shoes before each ride.
· Check the wear on disc brakes and the cables or hy-
draulic lines every 6 months to 1 year depending on
the conditions in which the bicycle is used. Flush the
hydraulic lines once a year.
PEDELEC SYSTEM COMPONENTS:
Regularly check the connections and cables of the ebike
system components. The connections must be clean and
free of debris and foreign objects. The cables must be in
good condition and free of cuts or kinks and bends that
may cause short circuits and lack of electric assistance.
-
The exterior of the controllers and batteries should not
show signs of damage that may allow water and other ele-
ments to ingress within.
ORBEA | 13
E N
-
-
-