Maytag MAT20PDFGW Instrucciones página 17

CODE
H.00 EXTRA RINSE Upgrade* - Represents the amount of Coins or
EXTRA Debit pulses required to purchase the Extra Rinse Upgrade.
RINSE Adjustable between 0 and 40. Factory default is set for 1 on PD
models and set for 0 on PR models.
g Press the NORMAL keypad once to advance to next code.
J.Cd COIN/DEBIT OPTION*
J.Cd Both coin and debit selected.
J.C_ Coins selected, debit disabled. Press the DELICATES keypad
three times for this selection.
J._d Debit Card selected, coins disabled. Press the DELICATES
keypad three times for this selection.
J.Ed Enhanced Debit is self-selected when a Generation 2 card reader
is installed in the washer. The Ed option cannot be manually
selected or deselected.
g Press the NORMAL keypad once to advance to next code.
L.00 PRICE SUPPRESSION OPTION*
This option causes the customer display to show "ADD"
or "AVAILABLE" rather than the amount of money to add.
(Used mainly in debit installations.)
L.00 Not Selected "OFF."
L.PS Selected "ON." Press the DELICATES keypad once for this
selection.
g Press the NORMAL kepad once to advance to next code.
CLEAR ESCROW OPTION*
n. CE
When selected, money held in escrow for 30 minutes without
further escrow or cycle activity will be cleared.
n. CE Selected "ON."
n. 00 Not selected "OFF." Press the DELICATES keypad once to
deselect this selection.
g Press the NORMAL keypad once to advance to next code.
A3.03 NORMAL Cycle Settings*. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specific settings. Normal is set to 03 from the
factory.
g Press the NORMAL keypad once to advance to next code.
A4.01 DELICATES Cycle Settings*. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specific settings. Delicates is set to 01 from the
factory.
g Press the NORMAL keypad once to advance to next code.
A5.1C POWERWASH Cycle Settings*. Allows the owner to select the
cycle default options of Water Temperature, Soil Level, and Extra
Rinse.
See Table 1 for specific settings. Powerwash is set to 1C from the
factory.
g Press the NORMAL keypad once to advance to next code.
A6.03 NORMAL ECO Cycle Settings*. Allows the owner to select the
cycle default options of Water Temperature, Soil Level, and Extra
Rinse.
See Table 1 for specific settings. Normal Eco is set to 03 from the
factory.
g Press the NORMAL keypad once to advance to next code.
F0 Wi-Fi MENU - Access Wi-Fi Menu by pressing the POWERWASH
button while on the "F0" screen. The Wi-Fi Menu allows you to
see Wi-Fi connection status as well as Wi-Fi setup options. See
the Wi-Fi Menu section for more information.
g Press the NORMAL keypad once to advance to next code.
EXPLANATION
Table 1
A3, A4, Extra Soil Level Water
A5, A6 Rinse (Heavy-On, Temp
Normal-Off)
00 Off Off Tap
Cold
01 Off Off Cold
02 Off Off Cool
03 Off Off Warm
04 Off Off Hot
08 Off On Tap
Cold
09 Off On Cold
a Off On Cool
B Off On Warm
C Off On Hot
Wi-Fi MENU
Pressing the POWERWASH key while on the F0 screen enters
into the Wi-Fi mode. To advance through the Wi-Fi sub menu, use
the MIXED key. The DELICATES key is the Select key. Press the
POWERWASH keypad at any time to exit Wi-Fi Menu.
CODE
F0.En Wi-Fi Enable/Disable option. This is either selected Enabled or Disabled.
F0.dS Wi-Fi disabled. Press the DELICATES key 3 times to disable Wi-Fi.
F0.En Wi-Fi Enabled. Press the DELICATES key 3 times to enable Wi-Fi.
g Press the NORMAL key once to advance to next code.
F1.dS Connection Status Mode (Status only) allows user to see machine's
current Wi-Fi connection status.
F1.dS (Status) This will be displayed if machine is not connected to router.
F1.Cr (Status) This will be displayed if machine is connected to router but
NOT connected with Whirlpool server.
F1.CS (Status) This will be displayed if machine is connected to router
AND connected with Whirlpool server.
g Press the NORMAL key once to advance to next code.
F2.En uAP Setup Mode allows machine to connect to Wi-Fi via uAP.
To begin connection process, connect the device (laptop) that is
being used to provision the machine, to the MAC Address of the
machine's Wi-FI Module. Next, open a web browser and direct it
to the address 192.168.10.1. This will direct you to the webpage
needed to complete the connection process.
F2.En This will be displayed if uAP provisioning is enabled and machine is
currently not connected to the router or Whirlpool server (default).
F2.dS This will be displayed if uAP provisioning is disabled and machine is
currently not connected to the router or Whirlpool server. In order to
disable setup via uAP press the DELICATES key 3 times.
F2.Cr (Status) This will be displayed if machine is connected to router but
NOT connected with Whirlpool server.
F2.CS (Status) This will be displayed if machine is connected to router
AND connected with Whirlpool server.
g Press the NORMAL key once to advance to next code.
F3.dS WPS Setup Mode allows machine to connect to Wi-Fi via WPS.
F3.dS This will be displayed if WPS provisioning is disabled and machine
is currently not connected to the router or Whirlpool server. This
will also be displayed if WPS connection not successful before the
WPS timer expired.
F3.En This and WPS countdown timer will toggle on the display if WPS
provisioning is enabled and machine is currently searching for the
router. Press the WPS button on the connecting router to complete
the connection.
A3, A4, Extra Soil Level
A5, A6 Rinse (Heavy-On,
Normal-Off)
10 On Off
11 On Off
12 On Off
13 On Off
14 On Off
18 On On
19 On On
1A On On
1B On On
1C On On
EXPLANATION
Water
Temp
Tap
Cold
Cold
Cool
Warm
Hot
Tap
Cold
Cold
Cool
Warm
Hot
17