Maytag MAT20PDFGW Instrucciones página 18

CODE
F3.Cr (Status) This will be displayed if machine is connected to router but
NOT connected with Whirlpool server.
F3.CS (Status) This will be displayed if machine is connected to router
AND connected with Whirlpool server.
g Press the NORMAL key once to advance to next code.
F4 Signal Strength Mode allows machine to show current signal
strength of Wi-Fi.
F4 Pressing the DELICATES key while on the F4 screen will toggle
between F4 and the signal strength in dBm.
g Press the NORMAL key once to advance to next code.
F5 Deprovision Mode allows machine to be disconnected from Wi-Fi.
F5 This will be displayed if no action is taken.
F5.dP This will flash on the display for 5 seconds while the machine
disconnects from Wi-Fi. In order to deprovision the machine press
the DELICATES key 3 times.
g Press the NORMAL key once to loop to beginning of this menu.
F3.dS WPS Setup Mode
F3 menu allows user to toggle between WPS or uAP Wi-Fi
connection. In order to toggle between uAP and WPS
connection, press DELICATES 3 times while on the F2.XX screen.
The F3 screen also acts as a status screen:
"F3.En" and WPS countdown timer will toggle on the display
n
if WPS provisioning is enabled and machine is currently
searching for the router.
"F3.dS" will be displayed if WPS provisioning is disabled and
n
machine is currently not connected to the router or Whirlpool
server. This will also be displayed if WPS connection not
successful before the WPS timer expired.
If cycle counter (9.0C) is selected, the following is true:
1 xx Number of cycles in THOUSANDS.
2xxx Number of cycles in ONES.
This is "VIEW ONLY" and cannot be cleared.
Press the NORMAL keypad once to advance
to next code.
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 xx Number in THOUSANDS.
4xxx Number in ONES.
5 xx Number of HUNDRETHS.
CONTROLS SET-UP THROUGH USB
To access the USB setup menu, navigate to set-up code 2.xx
(special pricing option). Pressing POWERWASH keypad activates
the help mode sub-menu. The first sub-mode within the help
mode is USB option. Press POWERWASH keypad at any time to
exit help mode.
S d
UbmOde eSCRIpTION
USB While on this screen, press the
POWERWASH button to enter into USB
menu. USB menu allows for software
update and import/export machine
settings.
18
EXPLANATION
1 02 = 2,000
2225 = 225
TOTAL CYCLES = 2,225
3 01 = $1,000.00
4600 = $ 600.00
5 75 = $ 00.75
TOTAL = $1,600.75
N
OTe
Allows user to enter
USB menu. See USB
MENU section for
more information.
USB MENU
To access USB menu enter into Help Mode. While on the USB
screen press the POWERWASH key. To advance through the
USB sub menu, use the MIXED key. The DELICATES key is the
Select key. Press the POWERWASH keypad at any time to exit
USB Menu.
See Page 19 for location of the USB Port on the appliance and
instructions for how to install a USB Stick onto the appliance and
to remove a USB stick from the appliance.
CODE
U0.00 USB drive Inserted? (Status only)
U0.00 This will be displayed if USB drive is NOT detected.
U0.01 This will be displayed if USB drive is detected.
g Press the NORMAL keypad once to advance to next code.
U1.00 Programming Mode.
U1.00 This will be displayed if USB drive not detected.
U1.01 This will be displayed if USB drive is detected. If you wish to
reprogram the controls Press the DELICATES key 3 times.
Display will toggle between U1.01 and ProG while programming
in process. Please wait until process is complete, this could take
several minutes. After software is successfully downloaded to
machine, the control could take several minutes to reset. After
reset is complete the machine will return to customer mode or
service mode depending on Service Switch status.
Err If the software programming was unsuccessfull the display will
toggle between U1.00 and Err.
g Press the NORMAL keypad once to advance to next code.
U2.00 Export Machine Settings to USB Drive.
U2.00 This will be displayed if USB drive is not detected.
U2.01 This will be displayed if USB drive is detected. If you wish to
export machine settings to USB drive press the DELICATES key
3 times. Display will toggle between U2.01 and --.-- while export
in process.
donE Display will toggle between U2 and donE when export finished
successfully.
Err If the export was unsuccessful the display will toggle between U2
and Err.
g Press the NORMAL keypad once to advance to next code.
U3.00 Import Machine Settings from USB Drive.
U3.00 This will be displayed if USB drive is not detected.
U3.01 This will be displayed if USB drive is detected. If you wish to
import machine settings from USB drive to machine press the
DELICATES key 3 times. Display will toggle between U3.01 and
--.-- while import in process.
donE Display will toggle between U3 and donE when import finished
successfully.
Err If the import was unsuccessful the display will toggle between U3
and Err.
g Press the NORMAL keypad once to advance to next code.
EXPLANATION